Audison

30 Products Found

AUDISON AP 1

FEATURES:

26 MM DIAMETER DIAPHRAGM COMBINED WITH A WIDE - ROLL SURROUND PROVIDES MAXIMUM EFFICIENCY AND REDUCED RESONANCE FREQUENCY.
NEODYMIUM MAGNET WITH LOW CARBON CONTENT PLATES, PROVIDES REDUCED SIZE AND MORE LINEAR SOUND REPRODUCTION, EVEN DURING THE MOST DEMANDING AUDIO PASSAGES.
ACOUSTIC LENS DESIGNED TO COMPENSATE FOR AND FINE TUNE THE IN - CAR FREQUENCY RESPONSE ANOMALIES IN THE 10 KHZ - 13 KHZ BANDWIDTH CAUSED BY RESTRICTIVE OEM GRILLES IN CRITICAL OEM PLACEMENTS.
EXTREMELY COMPACT DEDICATED PASSIVE CROSSOVER APCX TW SUPPLIED WITH THE PRODUCT, OPTIMISED FOR OEM INTEGRATION, FEATURING AN ATTENUATION SWITCH (0 DB, +2 DB) TO TUNE THE IN - CAR RESPONSE ACCORDING TO DIFFERENT INSTALLATION CONDITIONS.
PASSIVE CROSSOVERS ARE SUPPLIED WITH "OEM INTEGRATION COMPLIANT" FAST - ON CONNECTORS. THE ENDS, DIFFERENT IN EACH OF THE TWO POLES, ELIMINATE ANY POSSIBLE CONNECTION ERRORS AND SPEED UP THE REQUIRED INSTALLATION TIME.
WIDE ARRAY OF MOUNTING ACCESSORIES SUPPLIED WITH THE PRODUCT, FOR HIGH FITMENT FLEXIBILITY IN OEM INTEGRATION.
CCAW (COPPER CLAD ALUMINIUM WIRE) ULTRA - LIGHT FERROFLUID COOLED VOICE COIL IS WOUND ON A KAPTON FORMER, FOR BETTER HEAT DISSIPATION.
DOME PROFILE AND MOTOR ARE OPTIMISED WITH FEM (FINITE ELEMENT METHOD) SIMULATION TECHNOLOGY.
DEVELOPED WITH THE KLIPPEL SUITE.

SPECIFICATIONS:

COMPONENT TWEETER
SIZE MM (IN.) 26 (1)
POWER HANDLING:
- 150W PEAK HI - PASS FILTERED @ 3,5 KHZ - 12 DB OCT
IMPEDANCE Ω 4
FREQUENCY RESPONSE HZ 2K ÷ 20K
VOICE COIL Ø MM (IN.) 20 (0.8)
MOUNTING DIAMETER 38.5MM
MOUNTING DEPTH 8.MM
CROSSOVER INCLUDED

AUDISON AP6.5

COMP: WOOFER
SIZE: 165 MM (6,5")
POWER HANDLING: 70 W CONTINUOUS POWER, 210 W PEAK POWER
IMPEDANCE: 4 Ω
FREQUENCY RESPONSE: 60 ÷ 5K HZ
SENSITIVITY: 93,5 DB/SPL
MAGNET: HIGH DENSITY FLUX FERRITE
DOME: WATER-REPELLENT TREATED PAPER CONE

8% OFF

AUDISON AP8.9BIT

POWER OUTPUT

LOAD IMP.: 8 CHANNELS 4 CHANNELS (BRIDGE)
4 OHM: 35 W X 8 130 W X 4
2 OHM: 65 W X 8

ACCESSORIES

DRC - DIGITAL REMOTE CONTROL - THE DRC IS THE DIGITAL INTERFACE BETWEEN THE AP8.9 BIT AND THE USER. THE DRC MOUNTED IN THE VEHICLE DASHBOARD, PROVIDES ACCESS TO CONTROL OF THE INPUTS AND VOLUME ADJUSTMENTS, BALANCE, FADER AND SUBWOOFER VOLUME. PROVIDING SOURCE SELECTION BETWEEN MAIN, AUX AND OPTICAL INPUTS, IT ALSO PROVIDES FOUR OF THE CONFIGURATIONS CREATED AND SAVED BY THE BIT ONE RIGHT AT HAND. THE DRC ALSO CONTROLS THE FUNCTIONS OF THE AUDISON THESIS AMPLIFIERS WHEN THESE ARE INSTALLED IN THE SAME SYSTEM.
ECK DRC - DRC CABLE EXTENSION KIT FOR INSTALLATIONS ON ESPECIALLY LONG VEHICLES. TOTAL LENGTH OF THE SUPPLIED CABLE WITH THE EXTENSION IS EQUAL TO 6,5 M / 225,90".
OP 1.5 • TOSLINK OPTICAL CABLE - OPTICAL CABLE ENDING WITH TOSLINK CONNECTORS FOR S/PDIF DIGITAL AUDIO SIGNALS. CABLE LENGTH: 1,5 M / 59,05”.
OP 4.5 • TOSLINK OPTICAL CABLE - OPTICAL CABLE ENDING WITH TOSLINK CONNECTORS FOR S/PDIF DIGITAL AUDIO SIGNALS. CABLE LENGTH: 4,5 M/177,16”
STA • F/F SOCKET TOSLINK ADAPTER - OPTICAL ADAPTER TO EXTEND OPTICAL CABLES FEATURING TOSLINK CONNECTORS.
AP T-HARNESS “DCC”. - T-HARNESS “DCC” IS THE PLUG&PLAY SOLUTION TO INTEGRATE AUDISON PRIMA WITH THE FACTORY CAR AUDIO SYSTEM.
AP EXTENSION CABLES. - THE EXTENSION CABLE WITH PLUG&PLAY CONNECTIONS ALLOWS TOTAL FREEDOM IN POSITIONING THE AP BIT AMPLIFIERS.
AP SPEAKERS OUTPUT CABLES. - THE AP SPEAKERS OUTPUT FOR AP8.9 BIT IS DEDICATED TO THE CONNECTION OF THE AP BIT AMPLIFIERS WITH THE INPUT/OUTPUT EXTENSION CABLE.
APL 2 - (AP4 D / AP1 D) LINK CABLE - CABLE TO CONNECT AP8.9 BIT TO AP4 D AND AP1 D AMPLIFIERS.

FEATURES

EISA AWARD 2014-2015 - THE AP8.9 BIT BUILT-IN PROCESSOR AMPLIFIERR HAS BEEN GIVEN THE EISA AWARD FOR THE IN-CAR INTEGRATION CATEGORY, ATTAINING THE TITLE OF “EUROPEAN IN-CAR INTEGRATION 2014-2015".

AUDISON APBMWS84

FEATURES

NEODYMIUM MAGNETIC GROUP - TO MAXIMIZE PERFORMANCE WHILE MINIMIZING BULK AND WEIGHT
DEVELOPED WITH ELECTROACOUSTIC PARAMETERS CUSTOMIZED FOR BMW-MINI - TO INCREASE LISTENING ENGAGEMENT, THROUGH POWERFUL AND CRISP LOW FREQUENCIES, EXPLOITING THE ACOUSTIC LOAD PROVIDED BY THE FACTORY BOX
38 MM VOICE COIL WOUND ON ALUMINIUM SUPPORT - FOR A CONSIDERABLE POWER DISSIPATION AND STABILITY EVEN DURING HIGH EXCURSIONS
TWO 5 MM GASKETS PROVIDED - FOR OEM PLACEMENTS
2 OHM CONFIGURATION FOR MAXIMUM OUTPUT - IN COMBINATION WITH AP 8.9 BIT IN ACTIVE MULTI-AMPLIFICATION

SPECIFICATIONS

COMPONENT: WOOFER
SIZE MM (IN.): 200 (8)
IMPEDANCE Ω: 4
FREQUENCY RESPONSE HZ: 35 ÷ 500
MAGNET SIZE (D X D X H) MM (IN.): 48 (1.89) X 18 (0.71) X 7 (0.28)
WEIGHT OF ONE SPEAKER KG (LB.): 1,21 (2.67)
VOICE COIL Ø MM (IN.): 50 (2)

POWER HANDLING

W PEAK: 300
W CONTINUOUS: 150

AUDISON APBX8DS

COMP: SEALED SUB BOX
SUBWOOFER SIZE MM (IN.): 200 (8")
POWER HANDLING: 250 W CONTINUOUS POWER/500 W PEAK POWER
IMPEDANCE Ω: 4 Ω
SUB BOX SIZE MM (IN.): 377 (14.84) X 334 (13.15)X 109 (4.29)
MAGNET: HIGH DENSITY FLUX FERRITE
CONE: WATER-REPELLENT PRESSED PAPER
WEIGHT OF ONE COMPONENT: KG (LB) 6,22 (13.71)

AUDISON APBX8R

COMP: REFLEX SUB BOX
SUBWOOFER SIZE MM (IN.): 200 (8")
POWER HANDLING: 250 W CONTINUOUS POWER/500 W PEAK POWER
IMPEDANCE Ω: 4 Ω
SUB BOX SIZE MM (IN.): 473 (18.62) X 334 (13.15) X 109 (4.29)
MAGNET: HIGH DENSITY FLUX FERRITE
CONE: WATER-REPELLENT PRESSED PAPER
WEIGHT OF ONE COMPONENT: KG (LB) 6,64 (14.64)

AUDISON APBXG6

AUDISON APG5

AUDISON APG6.5

AUDISON APK130

COMP: 2 WAY SYSTEM
SIZE:
- 130 MM (5″) WOOFER
- 26 MM (1″) TWEETER
- 46,5 X 37,5 X 20,1 MM (1.83″ X 1.47 X 0.8) CROSSOVER
POWER HANDLING:
- 75W CONTINUOUS POWER
- 225W PEAK POWER
IMPEDANCE: 4 Ω
FREQUENCY RESPONSE: 70

AUDISON APK165

AUDISON APK1652O

SPECIFICATIONS

COMPONENT: 2-WAY SYSTEM
IMPEDANCE Ω: 2
FREQUENCY RESPONSE HZ: 50 ÷ 20K
CROSSOVER TYPE CUT OFF: @ 4.5 / 5 KHZ (HI-CONTOUR ON/OFF) -6DB OCT.
COMPONENT ADJUSTMENT: DB +2; 0

WOOFER MAGNET SIZE (D X D X H)

MM: 85 X 32 X 15
(IN.): (3.35 X 1.26 X 0.59)

TWEETER MAGNET SIZE (D X D X H)

MM 19 X 3
(IN.) (0.75 X 0.12)

WEIGHT OF ONE SPEAKER (KG/LB)

WOOFER: 0,78 (1.72)
TWEETER: 0,04 (0.09)

VOICE COIL Ø MM (IN.)

WOOFER: 25 (1)
TWEETER: 20 (0.8)

SIZE MM (IN.)

WOOFER: 165 (6.5)
TWEETER: 26 (1)

POWER HANDLING

W PEAK: 300
W CONTINUOS: 100

AUDISON APS10D

FEATURES

ULTRA-LOW PROFILE (4.7 IN. / 120 MM) FOR MAXIMUM INSTALLATION FLEXIBILITY
DESIGNED TO DELIVER MAXIMUM PERFORMANCE IN A SEALED ENCLOSURE STARTING FROM 10 LT
SPECIAL DESIGNED CONE-DUSTCAP-BASKET GEOMETRY WHICH GUARANTEES A LONG LINEAR EXCURSION CAPABILITY (11 MM, ONE-WAY) WHILE KEEPING THE MOUNTING DEPTH TO MINIMUM
AIR VENTS ON THE BASKET UNDERNEATH THE SPIDER, ELIMINATING THE NEED FOR THE CENTRAL POLE VENT ALLOWING MOUNTING CLOSE TO REAR WALL OF ENCLOSURE
MASSIVE MOTOR ASSEMBLY, OPTIMIZED WITH FEM (FINITE ELEMENT MODELING) FOR PERFECT CONTROL UNDER HIGH POWER, HIGH EXCURSION CONDITIONS
WATER-REPELLENT TREATED PAPER 10 IN. CONE, FEATURING A PROFILE DEVELOPED WITH FEM SIMULATION AND OPTIMIZED WITH THE KLIPPEL SCAN VIBROMETER
DUAL VOICE COIL DESIGN SPECIFICALLY DEVELOPED TO BE COMBINED WITH EITHER AP8.9 BIT (2 CH + 2 CH BRIDGED), AP5.9 BIT (SUB CH) OR AP4.9 BIT/AP4 D (2 CH BRIDGED) AMPLIFIERS
STEEL MESH GRILLE AND PLASTIC GASKET INCLUDED

SPECIFICATIONS

POWER HANDLING

W PEAK: 800
W CONTINUOS: 400

AUDISON APS8R

FEATURES:

ULTRA-LOW PROFILE (3.11 IN. / 79 MM) FOR MAXIMUM INSTALLATION FLEXIBILITY
DESIGNED TO DELIVER MAXIMUM PERFORMANCE IN A REFLEX ENCLOSURE STARTING FROM 8.5 LT
SPECIAL DESIGNED CONE-DUSTCAP-BASKET GEOMETRY WHICH GUARANTEES A LONG LINEAR EXCURSION CAPABILITY (ALMOST 9 MM, ONE-WAY) WHILE KEEPING THE MOUNTING DEPTH TO MINIMUM
AIR VENTS ON THE BASKET UNDERNEATH THE SPIDER, ELIMINATING THE NEED FOR THE CENTRAL POLE VENT ALLOWING MOUNTING CLOSE TO REAR WALL OF ENCLOSURE
MASSIVE MOTOR ASSEMBLY, OPTIMIZED WITH FEM (FINITE ELEMENT MODELING) FOR PERFECT CONTROL UNDER HIGH POWER, HIGH EXCURSION CONDITIONS
WATER-REPELLENT TREATED PAPER 8 IN. CONE, FEATURING A PROFILE DEVELOPED WITH FEM SIMULATION AND OPTIMIZED WITH THE KLIPPEL SCAN VIBROMETER
SPECIFICALLY DEVELOPED TO BE COMBINED WITH EITHER THE AUDISON AP8.9 BIT (2 CH BRIDGED) OR AP4.9 BIT /AP4 D (2 CH BRIDGED) AMPLIFIERS
STEEL MESH GRILLE AND PLASTIC GASKET INCLUDED

SPECIFICATIONS:

AUDISON APX4

COMP: TWO WAY COAXIAL
SIZE: WOOFER 100 MM (4"), TWEETER DIAPHRAGM 24 MM (0.9")
POWER HANDLING: 40 W CONTINUOUS POWER, 120 W PEAK POWER
IMPEDANCE: 4 Ω
FREQUENCY RESPONSE: 80 ÷ 23K HZ
SENSITIVITY: 91 DB/SPL
MAGNET: HIGH DENSITY FLUX FERRITE
DOME: WATER-REPELLENT PRESSED PAPER

AUDISON APX5

COMP: TWO WAY COAXIAL
SIZE: WOOFER 130 MM (5"), TWEETER DIAPHRAGM 24 MM (0.9")
POWER HANDLING: 50 W CONTINUOUS POWER, 150 W PEAK POWER
IMPEDANCE: 4 Ω
FREQUENCY RESPONSE: 70 ÷ 23K HZ
SENSITIVITY: 91 DB/SPL
MAGNET: HIGH DENSITY FLUX FERRITE
DOME: WATER-REPELLENT PRESSED PAPER

AUDISON APX570

COMP: TWO WAY COAXIAL
SIZE: WOOFER (5" X 7"), TWEETER DIAPHRAGM 24 MM (0.9")
POWER HANDLING: 70 W CONTINUOUS POWER, 210 W PEAK POWER
IMPEDANCE: 4 Ω
FREQUENCY RESPONSE: 60 ÷ 23K HZ
SENSITIVITY: 93 DB/SPL
MAGNET: HIGH DENSITY FLUX FERRITE
DOME: WATER-REPELLENT PRESSED PAPER

AUDISON APX6.5

COMP: TWO WAY COAXIAL
SIZE: WOOFER 165 MM (6,5") / TWEETER DIAPHRAGM 24 MM (0.9")
POWER HANDLING: 70 W CONTINUOUS POWER / 210 W PEAK POWER
IMPEDANCE: 4 Ω
FREQUENCY RESPONSE: 60 ÷ 23K HZ
SENSITIVITY: 94 DB/SPL
MAGNET: HIGH DENSITY FLUX FERRITE
DOME: WATER-REPELLENT PRESSED PAPER

AUDISON AVBIT

DISTORTION THD - 0.03%
BANDWIDTH - 5/20K HZ
S/N RATIO (A WEIGHTED @ 1V) - 98DB
DIGITAL RESOLUTION - 24 BIT/192 KHZ
INPUT/OUTPUT - AD LINK / AC LINK

AUDISON AVDUE

POWER OUTPUT

LOAD IMP.: STEREO MONO
4 OHM: 260 W X 2 900 W X 1
2 OHM: 450 W X 2

ACCESSORIES

AV BIT IN - DIGITAL INTERFACE FOR ALL AV AMPLIFIERS. IT OFFERS ONE AD LINK AND AC LINK INPUT AS WELL AS ONE AD LINK AND AC LINK OUTPUT FOR A PERFECT DIGITAL CONNECTION WITH DIGITAL PROCESSORS (BIT ONE AND BIT TEN D) TO DRIVE A MULTI-AMPLIFIED SYSTEM.
VCRA – REMOTE SUB VOLUME CONTROL - ANALOG REMOTE VOLUME CONTROL TO DRIVE THE SUBWOOFER IN MONO, BY CONNECTING THE EXTERNAL SUBWOOFER VOLUME TO THE SPECIAL SUB VOLUME SOCKET (ONLY WITH ANALOG INPUTS).

AUDISON AVGR6.5

AUDISON AVK5

AUDISON AVK6

AUDISON AVQUATTRO

POWER SUPPLY:
- POWER SUPPLY VOLTAGE: 11 ÷ 15 VDC
- IDLING CURRENT: 1.8 A
- IDLING CURRENT WHEN OFF: 0.02 MA
- CONSUMPTION @ 14.4 VDC (MAX MUSICAL POWER): 55 A
AMPLIFIER STAGE:
- DISTORTION - THD (1KHZ @ 4Ω): 0.04 %
- BANDWIDTH (-3 DB): 4 ÷ 60K HZ
- S/N RATIO (A WEIGHTED @ 1V): 100 DBA
- DAMPING FACTOR (1K HZ @ 4Ω): 100
- INPUT SENSITIVITY: 0.3 ÷ 5 V RMS
- INPUT IMPEDANCE: 15K Ω
- SPEAKER-IN SENSITIVITY: 1.4 ÷ 24 V RMS
- SPEAKER-IN IMPEDANCE: 5K Ω
- MINIMUM LOAD IMPEDANCE: 2Ω
- NOMINAL POWER (RMS) @ 12 VDC, THD 0.3%, 4Ω:100 W
OUTPUT POWER (RMS) @ 14.4 VDC,THD 1%:
- 4 CH: 120 W X 4 (4Ω)
- 4 CH: 200 W X 4 (2Ω)
- 4 CH: 120 W X 2 (4Ω) + 200 W X 2 (2Ω)
- 3 CH: 120 W X 2 (4Ω) + 400 W X 1 (4Ω)
- 3 CH: 200 W X 2 (2Ω) + 400 W X 1 (4Ω)
- 2 CH: 400 W X 1 (4Ω) + 400 W X 1 (4Ω)
CEA SPECIFICATIONS:
- OUTPUT POWER @ 4Ω, 1% THD+N, 14.4 V: 120 W X 4 CH
- SN RATIO (REF. 1 W OUTPUT): 80 DBA
SIGNALS INPUTS / FILTERS:
- INPUTS: PRE IN / SPEAKERS IN
- OUTPUTS: PRE OUT FULL RANGE
- A CH & B CH FILTERS (FULL / HI-PASS / LO-PASS): 50 ÷ 50K HZ (2 RANGE) @ 12 DB/OCT.
- B CH FILTER (LO-PASS 24 DB MONO): 50 ÷ 500 HZ @ 24 DB/OCT.
OTHER FUNCTIONS:
- REMOTE IN: 7 ÷ 15 VDC - 1MA
- REMOTE OUT: 12 VDC - 50MA
- FUSE (STRIP TYPE): 60 A
- REMOTE SUB VOLUME ADJ. (B CH LO-PASS 24 DB): (-50 ÷ 6) DB
- SPEAKERS IN TURN-ON (ART): SELECTABLE
SIZE/WEIGHT:
- MAX SIZE (MM/INCHES): 220 X 470 X 58 / 8,66” X 18,50” X 2,28”
- WEIGHT (KG/LB): 7.2 / 15.87

Filter By Series

Filter By Department

Filter By Peak Power Handling

Filter By Total Peak Power Output

Filter By Total Rms Power Output

Filter By RMS Power Handling

Filter By Impedance

Filter By Minimum Impedance Bridged

Filter By Number of Channels

Filter By Model

Filter By Minimum Impedance Unbridged

Filter By Slim Line

Filter By Weight (kg/lb)

Filter By Power Handling

Filter By Max size (mm/inches):

Filter By Comp

Filter By Size:

Filter By Power supply voltage

Filter By Idling current

Filter By Category

Filter By Price Range

Filter By Price Range

Categories

Information

Audison

About Us

Information

PaymentS

Community