Mono Channel Amplifiers

FEATURES:

• HIGH LEVEL INPUT CAPABLE WITH AUTO TURN-ON CIRCUIT
• FEATURES C.L.E.A.N. SET-UP
• OPTIONAL REMOTE PUNCH LEVEL CONTROL (PLC2) READY (W/ INPUT CLIP INDICATOR)
• 12DB/OCTAVE BUTTERWORTH CROSSOVER
• RCA PASS-THRU OUTPUTS
• ON-BOARD PUNCH EQ WITH +18DB BOOST @ 45HZ
• MUTED TURN ON
• STEALTH TOP MOUNTED CONTROL PANEL
• CAST ALUMINUM HEATSINK
• SHORT CIRCUIT PROTECTION
• OVER CURRENT PROTECTION
• INFRASONIC FILTER
• MARINE GRADE TWO PART EPOXY COATING ON CIRCUIT BOARDS
• MARINE GRADE STAINLESS STEEL HARDWARE

SPECIFICATIONS:

• RECOMMENDED FUSE (NOT INCLUDED) 140 A
• TOTAL HARMONIC DISTORTION (THD+NOISE) 4-OHM: <1.0%, 2-OHM: <1.0%, 1-OHM: <1.0%
• EFFICIENCY (AVERAGE) 86% @ 4-OHM
• DYNAMIC POWER (PVC/POWERCUBE®) 491 WATTS X 1 @ 4-OHMS, 874 WATTS X 1 @ 2-OHMS, 1,430 WATTS X 1 @ 1-OHM
• INPUT SENSITIVITY 150 MV - 12 V
• SHIPPING WEIGHT 12.9 LBS. (5.85 KG.)
• SIGNAL INPUT HI/LOW LEVEL: 1 RCA PAIR
• CEA-2006 COMPLIANT
• CEA-2006 POWER RATING 300W X 1 @ 4Ω, ≤1.0% THD+N
• BRIDGEABLE NO
• NUMBER OF CHANNELS 1
• SUGGESTED ALTERNATOR 100 A
• OPERATING VOLTAGE 9 - 16 VDC
• MAX. CURRENT DRAW (13.8V SINEWAVE) 130 A
• RATED POWER (RMS CONTINUOUS POWER) 300 WATTS X 1 @ 4-OHM, 500 WATTS X 1 @ 2-OHM, 1000 WATTS X 1 @ 1-OHM
• AVERAGE CURRENT DRAW (13.8V MUSIC) 65 A
• TOTAL POWER (SUM OF RATED POWER) 1000 WATTS
• CROSSOVER CONTROLS LOW-PASS (LP): 50-250HZ @ 12DB/OCTAVE BUTTERWORTH / INFRASONIC FILTER (IF): 28HZ @ 12DB/OCTAVE BUTTERWORTH / ALL-PASS: NO
• TONE CONTROLS PUNCH EQ2 BASS: 0DB TO +18DB @ 45HZ
• SIGNAL OUTPUT HI/LOW LEVEL: 1 RCA PAIR
• SPEAKER OUTPUT CONNECTOR CAPTIVE C-CLAMP
• POWER INPUT CONNECTOR CAPTIVE C-CLAMP
• POWER WIRE GAUGE 4 AWG
• SPEAKER WIRE GAUGE 8 AWG TO 18 AWG
• HEAT SINK TYPE CAST ALUMINUM
• COOLING CONVECTION
• REMOTE CONTROLS OPTIONAL PUNCH LEVEL CONTROL (PLC2) READY
• VISUAL INDICATORS POWER/PROTECT/THERMAL LED, INPUT CLIP LED3, OUTPUT CLIP LED1,2,3 / LED COLOR LEGEND: 1BLUE: <0.5% THD, 2VIOLET: 1% THD, 3RED: 10%+ THD
• CIRCUIT TOPOLOGY CLASS CLASS BD
• FREQUENCY RESPONSE 20HZ TO 250HZ +/- 1.0DB
• DIMENSIONS (H X W X D) 2.38 X 7.76 X 13.28 (IN) 6.05 X 19.71 X 33.73 (CM)

SPECIFICATIONS:

INPUTS:

• PREAMP INPUTS: 2 BALANCED
• PREAMP INPUT VOLTAGE RANGE: 500 MV – 6 V RMS
• SPEAKER LEVEL INPUTS: 2

OUTPUTS:

• RATED CONTINUOUS (RMS) POWER @ 14.4V:
  4 Ω – 175 W RMS
  2 Ω – 300 W RMS

PERFORMANCE:

• FREQUENCY RESPONSE: 10 HZ – 22 KHZ
• SIGNAL TO NOISE: 102 DBA, REF 175 W @ 4 OHM
• THD+N: < 0.01%
• POWER / GROUND WIRE GAUGE: 10 - 4 AWG WIRE
• FUSE RATING: 1 X 30 A
• CROSSOVER: 12 DB/OCTAVE LINKWITZ-RILEY, 80 HZ, 120 HZ, BYPASS
• PFM SUBSONIC FILTER: 24 HZ

WEIGHTS & DIMENSIONS:

• DIMENSIONS: 9.4″W X 3.0″D X 1.75″H
• WEIGHT: 2.1 LBS. (0.95KG)

FEATURES:

• SUBWOOFER AMPLIFIER WITH PATENTED ACCUBASS®
• 1500 WATTS @ 2 OHMS
• 800 WATTS @ 4 OHMS
• ACCUBASS® PROCESSING
• MILC™ MAXIMUM INPUT LEVEL CONTROL (PATENT PENDING)
• GTO™ SIGNAL SENSE
• 24 DB/OCTAVE LINKWITZ-RILEY ALIGNMENT CROSSOVER
• SPEAKER LEVEL & PREAMP INPUTS
• OPTIONAL ACR-1 ASSIGNABLE REMOTE CONTROL
• SOLID ONE-PIECE ALUMINUM CHASSIS
   

SPECIFICATIONS:

• RATED CONTINUOUS (RMS) POWER @ 14.4: 4Ω – 850W RMS / 2Ω – 1500W RMS
• HIGH-LEVEL INPUT VOLTAGE: 40V (400 WATTS) PER CHANNEL
• INPUT CHANNELS: 2 CHANNEL RCA + 2 CHANNEL HIGH LEVEL
• RCA PRE-OUTS: 2 CHANNEL STEREO
• REMOTE TURN ON FEATURE: YES
• TOTAL HARMONIC DISTORTION RATING: 0.01%
• CROSSOVER FREQUENCY: ADJUSTABLE FROM 30 HZ – 230 HZ
• CROSSOVER TYPE: 24 DB/OCTAVE LINKWITZ-RILEY
• DIMENSIONS: 12″W X 7.95″D X 2.1″H

FEATURES:

• SUBWOOFER AMPLIFIER WITH PATENTED ACCUBASS®
• 800 WATTS @ 2 OHMS
• 500 WATTS @ 4 OHMS
• ACCUBASS® PROCESSING
• MILC™ MAXIMUM INPUT LEVEL CONTROL (PATENT PENDING)
• GTO™ SIGNAL SENSE
• 24 DB/OCTAVE LINKWITZ-RILEY ALIGNMENT CROSSOVER
• SPEAKER LEVEL & PREAMP INPUTS
• OPTIONAL ACR-1 ASSIGNABLE REMOTE CONTROL
• SOLID ONE-PIECE ALUMINUM CHASSIS
   

SPECIFICATIONS:

• RATED CONTINUOUS (RMS) POWER @ 14.4: 4Ω – 500W RMS / 2Ω – 800W RMS
• HIGH-LEVEL INPUT VOLTAGE: 40V (400 WATTS) PER CHANNEL
• INPUT CHANNELS: 2 CHANNEL RCA + 2 CHANNEL HIGH LEVEL
• RCA PRE-OUTS: 2 CHANNEL STEREO
• REMOTE TURN ON FEATURE: YES
• TOTAL HARMONIC DISTORTION RATING: 0.01%
• CROSSOVER FREQUENCY: ADJUSTABLE FROM 30 HZ – 230 HZ
• CROSSOVER TYPE: 24 DB/OCTAVE LINKWITZ-RILEY
• DIMENSIONS: 9″W x 7.95″D x 2.1″H

• POWER @ 4-OHM: 200W × 1
• POWER @ 2-OHM: 300W × 1
• BRIDGED POWER @ 4-OHM: －
• NUMBER OF CHANNELS: 1
• MOS-FET POWER SUPPLY: YES
• 2-OHM STABLE: YES
• SELECTABLE BASS BOOST: 0-12DB @ 50HZ
• ADJUSTABLE 12DB/OCT. LOW PASS CROSSOVER: VARIABLE 35 - 250HZ
• NICKEL PLATED CONNECTORS: RCA/ SPEAKER/ POWER
• DIMENSIONS (W × H × D) (INCHES): 7.85 × 1.54 × 3.23

SPECIFICATIONS:

• CHANNELS: 1
• CONT POWER @ 2 OHM: 600W X 1CH
• DAMPING FACTOR: >100
• DIMENSIONS: 15.75″ X 9.45″ X 2.08″
• DYNAMIC POWER: 1200
• INPUT SENSITIVITY: 0.2V – 6V
• WIRE GAUGE (POWER & GROUND): SPADE TERMINAL
• WIRE GAUGE (SPEAKER OUTPUT): SPADE TERMINAL

FEATURES:

• ANGLE LOCK SET SCREW TERMINALS
• 24DB/OCT BANDPASS FILTERS
• DOUBLE SIDED-CONFORMAL COATED PCBS
• REMOTE GAIN CONTROL WITH A CLIPPING INDICATOR

SPECIFICATIONS:

• TEST VOLTAGE: 14.4
• CHANNELS: 1
• CONT WATTAGE: @ 4OHM 470
• CONT WATTAGE: @ 2OHM 770
• CONT WATTAGE: @ 1OHM 1000
• DYNAMIC WATTAGE: 1500
• MAX CURRENT DRAW: AMPERAGE 90
• S/N RATIO: >80DB
• THD: <0.5%
• INPUT VOLTAGE SENSITIVITY: 200MV~6V
• PASS-THROUGH OUTPUT: YES
• REMOTE SUBWOOFER CONTROL: YES
• POWER WIRE GAUGE IN: 4
• SPEAKER WIRE GAUGE OUT: 12
• DIMENSIONS: IN 11.8 X 4.92 X 1.85
• DIMENSIONS: MM 300 X 125 X 47

• TEST VOLTAGE: 14.4
• CHANNELS: 1
• CONT WATTAGE @ 4OHM: 580
• CONT WATTAGE @ 2OHM: 1000
• CONT WATTAGE @ 1OHM: 1500
• DYNAMIC WATTAGE: 2300
• MAX CURRENT WATTAGE DRAW – AMPS: 180
• RCA INPUT SENSITIVITY (VOLTS): 4 - 0.1V
• RCA INPUT S/N: > 85DB
• PASS-THROUGH OUTPUT: YES
• REMOTE SUBWOOFER CONTROL: YES (REMOTE INCLUDED IN BOX)
• POWER WIRE GAUGE – IN: 1
• SPEAKER WIRE GAUGE – OUT: 10
• DIMENSIONS (IN): 13.78 X 7 X 2
• DIMENSIONS (MM): 350 X 175 X 55

FEATURES:

• ANGLE LOCK SET SCREW TERMINALS
• 24DB/OCT BANDPASS FILTERS
• DOUBLE SIDED-CONFORMAL COATED PCBS
• REMOTE GAIN CONTROL WITH A CLIPPING INDICATOR

SPECIFICATIONS:

• TEST VOLTAGE: 14.4V
• CHANNELS: 1
• CONT WATTAGE: @ 4OHM 210
• CONT WATTAGE: @ 2OHM 380
• CONT WATTAGE: @ 1OHM 500
• DYNAMIC WATTAGE: 800
• MAX CURRENT DRAW: AMPERAGE 80A
• S/N RATIO: >80DB
• INPUT VOLTAGE SENSITIVITY: 4V-0.1V
• PASS-THROUGH OUTPUT: YES
• REMOTE SUBWOOFER CONTROL: YES
• POWER WIRE GAUGE IN: 4
• SPEAKER WIRE GAUGE OUT: 12
• DIMENSIONS: IN 7.87 X 4.92 X 1.85
• DIMENSIONS: MM 200 X 125 X 47

FEATURES:

• ACTIVE SUBWOOFER ENCLOSURE WITH INTEGRATED AMPLIFIER ALL IN ONE BOX.
• MOSFET POWER FOR HIGH SWITCHING SPEED & GREATER STABILITY.
• PORTED BASS ENCLOSURE INCREASES THE AMOUNT OF BASS YOUR WOOFER PRODUCES WITHOUT ADDING ANY ADDITIONAL POWER TO YOUR SYSTEM.
• LOW LEVEL INPUT FOR EASE OF USE WITH RCA LEADS & HIGH LEVEL SPEAKER INPUT.
• LOW PASS FILTER LIMITS THE AMOUNT OF HIGH FREQUENCY OUTPUT.
• SECRET CHANNEL TO HIDE AMPLIFIER CABLE FOR A CLEAN INSTALLATION.

SPECIFICATIONS:

• SIZE: DUAL 12"
• POWER HANDLING: 1800W PEAK / 600W RMS

SPECIFICATIONS:

• POWER (WATTS) 1200
• RMS POWER OUTPUT @ 14.4V 1% THD+N 200W X 1 (@4 OHM)
• RMS POWER OUTPUT @ 14.4V 1% THD+N 300W X 1 (@ 2 OHM)
• AMPLIFIER TYPE CLASS-AB
• NUMBER OF CHANNELS 1
• FREQUENCY RESPONSE 20HZ - 400HZ
• SIGNAL TO NOISE RATIO >50DB
• SUBSONIC CROSSOVER RANGE 10HZ - 40HZ
• HIGH AND LOW PASS CROSSOVER 12DB PER OCTAVE
• SUBSONIC FILTER 12DB PER OCTAVE
• LOW PASS CROSS OVER RANGE 50HZ - 400HZ
• BASS BOOST @ 45HZ 0 - +18DB
• LOW LEVEL INPUT RANGE 0.35 VOLTS TO 10 VOLTS
• HIGH LEVEL INPUT RANGE 1 VOLT TO 30 VOLTS
• MINIMUM LOAD IMPEDANCE 2 OHM
• DAMPING FACTOR GREATER THAN 200
• POWER REQUIREMENTS 12V DC (NEGATIVE GROUND)
• OPERATING VOLTAGE 10.5 - 16 VOLTS
• RECOMMENDED MINIMUM POWER/GROUND 4 GAUGE (AWG) CABLE
• LENGTH 336MM (13-1/4")
• WIDTH 200MM (7-7/8")
• HEIGHT 51MM (2")

• POWER OUTPUT 300WX1@2OHMS
• FREQUENCY RESPONSE 10-320HZ±3DB
• THD@ROP 1%
• INPUT SENSITIVITY 0.2V-5V
• LOW PASS FILTER, VARIABLE 32 -320HZ
• BASS EQ 40HZ -100HZ 0-12DB
• PROTECTION DC, OVP, UVP, OCP, OTP

• MAXIMUM POWER OUTPUT: 800W
• RMS POWER OUTPUT (4 OHM) [ 1% THD 14.4V]: 250W X 1 (20 - 200HZ)
• RMS POWER OUTPUT (2 OHM) [ 1% THD 14.4V]: 400W X 1 (20 - 200HZ)
• CLASS: CLASS-D
• FREQUENCY RESPONSE (+0, -3DB): 20 - 200HZ
• TOTAL HARMONIC DISTORTION: < 0.08%
• SIGNAL-TO-NOISE RATIO (REFERENCE: 1W INTO 4 OHMS), CEA-2006 COMPLIANT: > 60DB
• LOAD IMPEDANCE ALLOWANCE: 2 - 8 OHMS
• LPF: 50 - 200H (18DB)
• SUBSONIC FILTER: 20HZ FIX
• RCA INPUT: L/R
• HIGH LEVEL INPUT (SPEAKER LEVEL INPUT): YES
• HIGH LEVEL INPUT AUTO POWER CONTROL (SIGNAL SENSING TURN ON): YES
• INPUT SENSITIVITY: 0.2 - 15V
• BASS BOOST CONTROL AT 45HZ VARIABLE: (0-18DB)
• PROTECTION CIRCUITRY (THERMAL / SHORT CIRCUIT / OVERLOAD / DC OFFSET): YES
• ANTI-POP CIRCUIT: YES
• DIMENSIONS: (W X H X D) 227 X 52 X 185

FEATURES:

• PEAK POWER 400W
• CONFORMAL COATING FOR MARINE AND OTHER USE.
• SPEAKER LEVEL INPUT WITH SIGNAL SENSING TURN ON.
• BRIDGEABLE CONNECTION.
• COMPACT DESIGN ( W)5-11/16" X (H)1-3/4" X (D)3-7/8"

SPECIFICATIONS:

• MAX POWER 400W
• RMS POWER 45W X 4 (4Ω)  / 45W X 4 (2Ω) / 90W X 2 (BRIDGED)
• S/N SIGNAL TO NOISE RATIO: 98 DB
• SIZE (W) 5-11/16” X (H) 1-3/4” X (D) 3-7/8”
• LOW PASS FILTER 50HZ-200HZ, -12DB/OCT (A/B)
• HIGH PASS FILTER 50HZ-200HZ, -12DB/OCT (A/B)
• SPEAKER LEVEL INPUT
• SIGNAL SENSING TURN-ON
• VARIABLE HIGH & LOW PASS FILTER
• BRIDGEABLE
• CONFORMAL COATING

FEATURES:

• MAX POWER 1000W
• SIZE (INCH) (W) 8-3/8" X (H) 2-1/16" X (D) 5-7/8"
• VARIABLE LOW PASS FILTER
• BASS BOOST
• OPTIONAL WIRED REMOTE READY

SPECIFICATIONS:

GENERAL

• MAX POWER 1000W
• RMS POWER OUTPUT (4Ω) 300W
• RMS POWER OUTPUT (2Ω) 500W

DIMENSIONS

• (W) 8-3/8” X (H) 2-1/16” X (D) 5-7/8”
• WEIGHT 3.1 LBS ( 1.4 KG)

FEATURES:

• ADAPTIVE CLASS-D TECHNOLOGY
• WIRED REMOTE BASS LEVEL CONTROL INCLUDED.
• LED POWER, OVERHEAT, & VOLTAGE INDICATORS.
• TUNED BASS EQ (0-12 DB BASS BOOST @ 40 HZ)
• JACKSTANDS ARE INCLUDED, WHICH ARE MOUNTING PLATFORMS THAT ENABLES A USER TO MOUNT UP TO THREE AMPLIFIERS.
• GAIN CONTROL
• BUILT-IN ACTIVE FAN COOLING TECHNOLOGY ADJUSTS FAN SPEED ACCORDING TO THE USAGE OF THE AMPLIFIER.
• NICKEL-PLATED RCA LEVEL INPUTS.
• NICKEL-PLATED SCREW TERMINALS.
• VARIABLE LOW-PASS FILTER (40-200 HZ, 24 DB/OCTAVE)
• SUBSONIC FILTER (20-50 HZ, 12 DB/OCTAVE)
• CEA-2006 COMPLIANT AMPLIFIER.

SPECIFICATIONS: 

• CONTINUOUS POWER / CHANNEL: 350 WATTS X 1
• FREQUENCY RESPONSE: 20 - 200 HZ
• SIGNAL-TO-NOISE RATIO: 70 DB
• AMPLIFIER OUTPUT: 1-CHANNEL
• OUTPUT POWER / TOTAL: 350 WATT
• INPUT SIGNAL VOLTAGE: 0.25 - 5V
• AMPLIFIER CLASS: CLASS D
• DISTORTION FACTOR: 1%
• OUTPUT POWER / CHANNEL: 350 WATT, 600 WATT
• OUTPUT IMPEDANCE / CHANNEL: 2 OHM, 4 OHM
• TOTAL HARMONIC DISTORTION: 1.0 %
• SUPPLY VOLTAGE: 14.4V DC
• CHANNEL QTY: 1
• TYPE: ACTIVE CROSSOVER
• CROSSOVER SLOPE: 24 DB
• LOW PASS FREQUENCIES: 40 - 200 HZ
• BASS BOOST FREQUENCY: 40 HZ
• BASS BOOST GAIN: 0 TO +12DB

FEATURES:

• FULL ALUMINIUM DESIGN
• HIGH END CONSTRUCTION
• VARIABLE ACTIVE CROSSOVER
• HIGH LEVEL INPUTS
• EBC (EXTERNAL BASS CONTROL)
• PWM MOSFET POWER SUPPLY
• SAFE & SECURE CONNECTION TERMINALS.
   

SPECIFICATIONS:

• CEA RMS POWER: 1X 500 W @ 2 OHM, THD+N ≤1%
• CEA RMS POWER: 1X 300 W @ 4 OHM, THD+N ≤1%
• HIGH PASS X-OVER: 12D B/OCT VARIABLE FROM 40 - 400 HZ
• LOW PASS X-OVER: 12D B/OCT VARIABLE FROM 40 - 400 HZ
• SIGNAL-TO-NOISE RATIO (1 WATT): > 80D B
• THD+NOISE (DISTORTION) (1 WATT): ≤ 1%
• FREQUENCY RESPONSE (±1D B): 20 HZ - 30000 HZ
• MAXIMUM INPUT SIGNAL: 6 V
• MAXIMUM SENSITIVITY: 100M V
• DIMENSIONS: 430 x 180 x 55mm

FEATURES:

• PATENTED ADAPTIVE CLASS D TECHNOLOGY.
• PATENTED SMART ENGAGE AUTO TURN ON.
• SURFACE MOUNT DESIGN.
• DUAL SIDED FIBERGLASS PRINTED CIRCUIT BOARD.
• CONVECTION COOLED DESIGN.
   

FEATURES:

• PATENTED ADAPTIVE CLASS D TECHNOLOGY
• PATENTED SMART ENGAGE AUTO TURN ON
• SURFACE MOUNT DESIGN
• DUAL SIDED FIBERGLASS PRINTED CIRCUIT BOARD
• CONVECTION COOLED DESIGN
   

FEATURES:

• PATENTED ADAPTIVE CLASS D TECHNOLOGY
• PATENTED SMART ENGAGE AUTO TURN ON
• SURFACE MOUNT DESIGN
• DUAL SIDED FIBERGLASS PRINTED CIRCUIT BOARD
• CONVECTION COOLED DESIGN

SPECIFICATIONS:

• PEAK: 900W
• RMS: 300W
• GAIN: 0.25V - 5V
• SUB SONIC: 20HZ - 50HZ
• BASS BOOST: 0 - 12DB
• LPF: 40HZ - 200HZ

• RMS POWER RATING: 4 OHMS: 375 WATTS X 1 CHAN. / 2 OHMS: 550 WATTS X 1 CHAN.
• MAX POWER OUTPUT: 1100 WATTS
• MOSFET POWER SUPPLY
• WIRED BASS REMOTE CONTROL INCLUDED
• TRI-MODE AND BRIDGEABLE OPERATION
• LED POWER AND PROTECT INDICATORS
• ILLUMINATED BLUE LED STRIPE DESIGN
• VARIABLE BASS BOOST (0-18 DB)
• MONO CHANNEL OPERATION
• 3-WAY SYSTEM PROTECTION CIRCUITRY (THERMAL, SHORT CIRCUIT, AND OVERLOAD)
• HEAVY DUTY ALUMINUM ALLOY CONVECTION HEATSINK
• INPUT SENSITIVITY (250MV-5V)
• VARIABLE LOW-PASS FILTER (15-400 HZ, 12 DB/OCTAVE)
• SUBSONIC FILTER (25 HZ)
• CEA-2006 COMPLIANT AMPLIFIER
• FREQUENCY RESPONSE: 20-30,000 HZ
• DIMENSIONS: 13-3/16"L X 7-1/2"W X 2"H
• 8-GAUGE POWER AND GROUND WIRING IS REQUIRED FOR INSTALLATION

• RMS POWER RATING: 4 OHMS: 400 WATTS X 1 CHAN. / 2 OHMS: 800 WATTS X 1 CHAN. / 1 OHM: 1200 WATTS X 1 CHAN.
• MAX POWER OUTPUT: 2400 WATTS
• MOSFET POWER SUPPLY
• WIRED BASS REMOTE CONTROL INCLUDED
• TRI-MODE AND BRIDGEABLE OPERATION
• LED POWER AND PROTECT INDICATORS
• ILLUMINATED BLUE LED STRIPE DESIGN
• VARIABLE BASS BOOST (0-18 DB)
• MONO CHANNEL OPERATION
• 3-WAY SYSTEM PROTECTION CIRCUITRY (THERMAL, SHORT CIRCUIT, AND OVERLOAD)
• HEAVY DUTY ALUMINUM ALLOY CONVECTION HEATSINK
• INPUT SENSITIVITY (150MV-5V)
• VARIABLE LOW-PASS FILTER (15-400 HZ)
• SUBSONIC FILTER (25 HZ)
• CEA-2006 COMPLIANT AMPLIFIER
• FREQUENCY RESPONSE: 20-30,000 HZ
• DIMENSIONS: 14-15/16"L X 7-1/2"W X 2"H
• 1/0-GAUGE POWER AND GROUND WIRING IS REQUIRED FOR INSTALLATION

• RMS POWER RATING: 4 OHMS: 250 WATTS X 1 CHAN. / 2 OHMS: 400 WATTS X 1 CHAN.
• MAX POWER OUTPUT: 700 WATTS
• MOSFET POWER SUPPLY
• WIRED BASS REMOTE CONTROL INCLUDED
• TRI-MODE AND BRIDGEABLE OPERATION
• LED POWER AND PROTECT INDICATORS
• ILLUMINATED BLUE LED STRIPE DESIGN
• VARIABLE BASS BOOST (0-18 DB)
• MONO CHANNEL OPERATION
• 3-WAY SYSTEM PROTECTION CIRCUITRY (THERMAL, SHORT CIRCUIT, AND OVERLOAD)
• HEAVY DUTY ALUMINUM ALLOY CONVECTION HEATSINK
• INPUT SENSITIVITY (250MV-5V)
• VARIABLE LOW-PASS FILTER (15-400 HZ, 12 DB/OCTAVE)
• SUBSONIC FILTER (25 HZ)
• CEA-2006 COMPLIANT AMPLIFIER
• FREQUENCY RESPONSE: 20-30,000 HZ
• DIMENSIONS: 13-3/16"L X 7-1/2"W X 2"H
• 8-GAUGE POWER AND GROUND WIRING IS REQUIRED FOR INSTALLATION