Multi Channel Amplifiers

• AMPLIFIER TYPE: CLASS-AB
• BASS BOOST @ 45HZ: 0 - +18DB
• CROSSOVER RANGE: 50HZ - 400HZ
• DAMPING FACTOR: GREATER THAN 200
• FREQUENCY RESPONSE: 20HZ - 20KHZ
• HIGH AND LOW PASS CROSSOVER: 12DB PER OCTAVE
• HIGH LEVEL INPUT RANGE: 1 VOLT TO 30 VOLTS
• LOW LEVEL INPUT RANGE: 0.35 VOLTS TO 10 VOLTS
• MINIMUM LOAD IMPEDANCE: 2 OHM STEREO AND 4 OHM BRIDGED
• NUMBER OF CHANNELS: 2
• OPERATING VOLTAGE: 10.5 - 16 VOLTS
• POWER (WATTS): 1200
• POWER REQUIREMENTS: 12V DC (NEGATIVE GROUND)
• RECOMMENDED MINIMUM POWER/GROUND: 4 GAUGE (AWG) CABLE
• RMS POWER OUTPUT @ 14.4V 1% THD+N: 90W X 2 (@ 2 OHM)
• RMS POWER OUTPUT @ 14.4V 1% THD+N: 180W X 1 (@4 OHM BRIDGED)
• RMS POWER OUTPUT @ 14.4V 1% THD+N: 65W X 2 (@ 4 OHM)
• SIGNAL TO NOISE RATIO: >50DB

• NUMBER OF CHANNELS: 4/3/2
• MAX WATTAGE (4 OHM): 170WX4
• MAX WATTAGE (2 OHM): 250W X4
• MAX WATTAGE BRIDGED (4 OHM): 500W X2
• FREQUENCY RESPONSE: 10HZ TO 70KHZ
• WATTAGE RMS (4 OHM <=1% THD+N): 60W X4
• WATTAGE RMS (2 OHM <=1% THD+N): 95W X4
• WATTAGE RMS BRIDGED (4 OHM): 190W X2
• TOTAL HARMONIC DISTORTION (1 KHZ, 4 OHM): <0.05%
• SIGNAL-TO-NOISE RATIO (IHF-A WEIGHTED): >95DB
• RCA OUTPUTS (PASS-THROUGH):
• SPEAKER LEVEL INPUT:
• AUTOMATIC SIGNAL SENSING: YES
• CROSSOVER FREQUENCY: 40HZ TO 500HZ
• CROSSOVER TYPE: VARIABLE HPF (HIGH PASS FILTER)
• DIMENSIONS: 356MM X 60MM X 215MM

• NUMBER OF CHANNELS: MONO
• MAX. WATTAGE (4 Ω): 600 W X 1
• MAX. WATTAGE (2 Ω): 1,000 W X 1
• MAX. WATTAGE (1 Ω): 1,600 W X 1
• WATTAGE RMS (4 Ω <= 1%THD+N): 300 W X 1
• WATTAGE RMS (2 Ω <= 1%THD+N): 500 W X 1
• WATTAGE RMS (1 Ω <= 1%THD+N): 800 W X 1
• FREQUENCY RESPONSE: 10 HZ TO 240 HZ
• TOTAL HARMONIC DISTORTION (1KHZ, 4 Ω): < 0.5% (100 HZ)
• SIGNAL-TO-NOISE RATIO (IHF-A WEIGHTED): > 100 DB
• DIMENSIONS (W X H X D): 265 MM X 60 MM X 200 MM

• NUMBER OF CHANNELS: 2/1
• MAX WATTAGE (4 OHM): 170WX2
• MAX WATTAGE (2 OHM): 250W X2
• MAX WATTAGE BRIDGED (4 OHM): 500W X1
• FREQUENCY RESPONSE: 10HZ TO 70KHZ
• WATTAGE RMS (4 OHM <=1% THD+N): 60W X2
• WATTAGE RMS (2 OHM <=1% THD+N): 95W X2
• WATTAGE RMS BRIDGED (4 OHM): 190W X1
• TOTAL HARMONIC DISTORTION (1 KHZ, 4 OHM): <0.05%
• SIGNAL-TO-NOISE RATIO (IHF-A WEIGHTED): >95DB
• RCA OUTPUTS (PASS-THROUGH): NA
• SPEAKER LEVEL INPUT: NA
• AUTOMATIC SIGNAL SENSING: YES
• CROSSOVER FREQUENCY: NA
• CROSSOVER TYPE: NA
• DIMENSIONS: 246MM X 60MM X 180MM

• NUMBER OF CHANNELS: 4 / 3 / 2
• MAX. WATTAGE (4 Ω): 200 W X 4
• MAX. WATTAGE (2 Ω): 300 W X 4
• MAX. WATTAGE (1 Ω): 250 W X 4
• MAX. WATTAGE BRIDGED (4 Ω): 600 W X 2
• WATTAGE RMS (4 Ω <= 1%THD+N): 100 W X 4
• WATTAGE RMS (2 Ω <= 1%THD+N): 150 W X 4
• WATTAGE RMS (1 Ω <= 1%THD+N): 125 W X 4
• WATTAGE RMS BRIDGED (4 Ω): 300 W X 2
• FREQUENCY RESPONSE: 10 HZ TO 50 KHZ
• TOTAL HARMONIC DISTORTION (1KHZ, 4 Ω): < 0.05%
• SIGNAL-TO-NOISE RATIO (IHF-A WEIGHTED): > 95 DB
• DIMENSIONS (W X H X D): 265 MM X 60 MM X 200 MM

• NUMBER OF CHANNELS: 4/3/2
• MAX. WATTAGE (4 Ω): 260 W X 4
• MAX. WATTAGE (2 Ω): 400 W X 4
• MAX. WATTAGE (1 Ω): 260 W X 4
• MAX. WATTAGE BRIDGED (4 Ω): 800 W X 2
• WATTAGE RMS (4 Ω <= 1%THD+N): 130 W X 4
• WATTAGE RMS (2 Ω <= 1%THD+N): 200 W X 4
• WATTAGE RMS (1 Ω <= 1%THD+N): 130 W X 4
• WATTAGE RMS BRIDGED (4 Ω): 400 W X 2
• FREQUENCY RESPONSE: 10 HZ TO 50 KHZ
• TOTAL HARMONIC DISTORTION (1KHZ, 4 Ω): <0.05 %
• SIGNAL-TO-NOISE RATIO (IHF-A WEIGHTED): >95 DB
• DIMENSIONS (W X H X D): 315 MM X 60 MM X 200 MM

• NUMBER OF CHANNELS: 5 / 4 / 3 / 2
• MAX. WATTAGE (4 Ω): 150W X 4 (A/B), 700W (SUB)
• MAX. WATTAGE (2 Ω): 200W X 4 (A/B), 1200W (SUB)
• MAX. WATTAGE BRIDGED (4 Ω): 400 W X 2 (A & B)
• WATTAGE RMS (4 Ω <= 1%THD+N): 75W X 4 (A/B), 350W (SUB)
• WATTAGE RMS (2 Ω <= 1%THD+N): 100W X4 (A/B), 600W (SUB)
• WATTAGE RMS BRIDGED (4 Ω): 200 W X 2 (A & B)
• FREQUENCY RESPONSE: A/B CH: 10HZ ~ 50KHZ (+0DB, -3DB) / SUB CH: 10HZ ~ 500HZ (+0DB, -3DB)
• TOTAL HARMONIC DISTORTION (1KHZ, 4 Ω): A/B CH: <0.05% (1KHZ) / SUB CH: <0.05% (100HZ)
• SIGNAL-TO-NOISE RATIO (IHF-A WEIGHTED): > 94 DB
• DIMENSIONS (W X H X D): 315 MM X 60 MM X 200 MM

• NUMBER OF CHANNELS: 4 - CHANNEL
• MINIMUM IMPEDANCE UNBRIDGED: 2 OHM
• MINIMUM IMPEDANCE BRIDGED: 2 OHM
• BASS/GAIN REMOTE: OPTIONAL
• SPEAKER LEVEL INPUTS: NO
• MAXIMUM INPUT GAUGE SIZE: 4 GAUGE
• AMPLIFIER CLASS: AD
• SERIES: POWER (ROCKFORD FOSGATE)
• BUILT IN CROSSOVER: FULL (AP)
• BRAND: ROCKFORD FOSGATE
• MARINE: NO
• COMBINED RMS POWER OUTPUT: 1308
• COMBINED PEAK POWER OUTPUT: 1308
• DIMENSIONS: 54 X 206 X 378
• RMS OUTPUT @ 4 OHMS: 270 X 4
• RMS OUTPUT @ 2 OHMS: 327 X 4
• RMS OUTPUT @ 1 OHM: 250 X 4 
• RMS OUTPUT BRIDGED @ 4 OHMS: 500 X 2

POWER OUTPUT

• LOAD IMP.: 5 CHANNELS
• 4 OHM: 75 W X 2 + 140 W X 2 + 600 W X 1
• 4/2 OHM: 75 W X 2 + 140 W X 2 + 1000 W X 1
• 2/4 OHM: 75 W X 2 + 250 W X 2 + 1000 W X 1

ACCESSORIES

• AV BIT IN - DIGITAL INTERFACE FOR ALL AV AMPLIFIERS. IT OFFERS ONE AD LINK AND AC LINK INPUT AS WELL AS ONE AD LINK AND AC LINK OUTPUT FOR A PERFECT DIGITAL CONNECTION WITH DIGITAL PROCESSORS (BIT ONE AND BIT TEN D) TO DRIVE A MULTI-AMPLIFIED SYSTEM. 
• VCRA – REMOTE SUB VOLUME CONTROL - ANALOG REMOTE VOLUME CONTROL TO DRIVE THE SUBWOOFER IN MONO, BY CONNECTING THE EXTERNAL SUBWOOFER VOLUME TO THE SPECIAL SUB VOLUME SOCKET (ONLY WITH ANALOG INPUTS).

POWER OUTPUT

• LOAD IMP.: STEREO MONO
• 4 OHM: 260 W X 2 900 W X 1
• 2 OHM: 450 W X 2

ACCESSORIES

• AV BIT IN - DIGITAL INTERFACE FOR ALL AV AMPLIFIERS. IT OFFERS ONE AD LINK AND AC LINK INPUT AS WELL AS ONE AD LINK AND AC LINK OUTPUT FOR A PERFECT DIGITAL CONNECTION WITH DIGITAL PROCESSORS (BIT ONE AND BIT TEN D) TO DRIVE A MULTI-AMPLIFIED SYSTEM. 
• VCRA – REMOTE SUB VOLUME CONTROL - ANALOG REMOTE VOLUME CONTROL TO DRIVE THE SUBWOOFER IN MONO, BY CONNECTING THE EXTERNAL SUBWOOFER VOLUME TO THE SPECIAL SUB VOLUME SOCKET (ONLY WITH ANALOG INPUTS).

POWER SUPPLY

• POWER SUPPLY VOLTAGE: 11 ÷ 15 VDC
• IDLING CURRENT: 1.8 A
• IDLING CURRENT WHEN OFF: 0.02 MA
• CONSUMPTION @ 14.4 VDC (MAX MUSICAL POWER): 55 A

AMPLIFIER STAGE

• DISTORTION - THD (1KHZ @ 4Ω): 0.04 %
• BANDWIDTH (-3 DB): 4 ÷ 60K HZ
• S/N RATIO (A WEIGHTED @ 1V): 100 DBA
• DAMPING FACTOR (1K HZ @ 4Ω): 100
• INPUT SENSITIVITY: 0.3 ÷ 5 V RMS
• INPUT IMPEDANCE: 15K Ω
• SPEAKER-IN SENSITIVITY: 1.4 ÷ 24 V RMS
• SPEAKER-IN IMPEDANCE: 5K Ω
• MINIMUM LOAD IMPEDANCE: 2Ω
• NOMINAL POWER (RMS) @ 12 VDC, THD 0.3%, 4Ω:100 W

OUTPUT POWER (RMS) @ 14.4 VDC, THD 1%

• 4 CH: 120 W X 4 (4Ω)
• 4 CH: 200 W X 4 (2Ω)
• 4 CH: 120 W X 2 (4Ω) + 200 W X 2 (2Ω)
• 3 CH: 120 W X 2 (4Ω) + 400 W X 1 (4Ω)
• 3 CH: 200 W X 2 (2Ω) + 400 W X 1 (4Ω)
• 2 CH: 400 W X 1 (4Ω) + 400 W X 1 (4Ω)

CEA SPECIFICATIONS

• OUTPUT POWER @ 4Ω, 1% THD+N, 14.4 V: 120 W X 4 CH
• SN RATIO (REF. 1 W OUTPUT): 80 DBA

SIGNAL INPUTS / FILTERS

• INPUTS: PRE IN / SPEAKERS IN
• OUTPUTS: PRE OUT FULL RANGE
• A CH & B CH FILTERS (FULL / HI-PASS / LO-PASS): 50 ÷ 50K HZ (2 RANGE) @ 12 DB/OCT.
• B CH FILTER (LO-PASS 24 DB MONO): 50 ÷ 500 HZ @ 24 DB/OCT.

OTHER FUNCTIONS

• REMOTE IN: 7 ÷ 15 VDC - 1MA
• REMOTE OUT: 12 VDC - 50MA
• FUSE (STRIP TYPE): 60 A
• REMOTE SUB VOLUME ADJ. (B CH LO-PASS 24 DB): (-50 ÷ 6) DB
• SPEAKERS IN TURN-ON (ART): SELECTABLE

SIZE / WEIGHT

• MAX SIZE (MM/INCHES): 220 X 470 X 58 / 8,66” X 18,50” X 2,28”
• WEIGHT (KG/LB): 7.2 / 15.87

ACCESSORIES

• AV BIT IN HD - DIGITAL INTERFACE FOR ALL AV AMPLIFIERS, FOR PERFECT DIGITAL CONNECTION WITH AUDISON BIT PROCESSORS PROVIDED WITH AD LINK AND AC LINK CONNECTIONS. BY MOUNTING THE AV BIT IN “DIGITAL INTERFACE” ONTO THE VOCE AMPLIFIER SERIES, THROUGH THE AD LINK CONNECTION THE S/PDIF DIGITAL SIGNAL WILL GET DIRECTLY TO THE HIGH QUALITY INTERNAL D/A CONVERTERS. AFTER THESE, THE SIGNAL BECOMES ANALOG AND IS IMMEDIATELY AMPLIFIED PREVENTING IT FROM DETERIORATION DUE TO THE LONG PATHS. THE RESULT IS EXTREMELY HIGH QUALITY MUSIC, NOT ACHIEVABLE WITH ANY OTHER ANALOG SYSTEM. IT OFFERS ONE AD LINK AND AC LINK INPUT, AS WELL AS ONE AD LINK AND AC LINK OUTPUT IN ORDER TO DRIVE A MULTI-AMPLIFIED SYSTEM. THANKS TO ITS DIGITAL PANEL WITH 3 CHARACTER DISPLAY AND 4 PUSH BUTTONS, YOU CAN SELECT THE AMPLIFIER TYPE, MONO OR STEREO MODE, AND ALSO THE DIGITAL CHANNEL COMING FROM THE AUDIO PROCESSOR. AV BIT IN HD FEATURES TWO NEW SWITCHES ON THE FRONT PANEL: ONE PROVIDES YOU WITH THE ABILITY OF TURNING OFF THE GAIN CONTROL OF THE AMPLIFIER TO ACHIEVE AN IMPROVED SIGNAL TO NOISE RATIO. WITH THE SECOND SWITCH YOU CAN CONTROL THE DSP REMOTE START FUNCTION. CONNECTION TO AMPLIFIER: REMOVE ANALOG CROSSOVER MODULE AND INSERT AV BIT IN MODULE INTO THE AMPLIFIER’S FRONT SIDE. IT REQUIRES NO EXTERNAL POWER SUPPLY.
• VCRA – REMOTE SUB VOLUME CONTROL - WHEN YOU DRIVE THE SUBWOOFER IN MONO, YOU CAN USE VCRA ANALOG REMOTE CONTROL BY CONNECTING THE EXTERNAL SUBWOOFER VOLUME TO THE SPECIAL SUB VOL SOCKET.

POWER OUTPUT

• LOAD IMP.: MONO
• 4 OHM: 700 W X 1
• 2 OHM: 1300 W X 1
• 1 OHM: 1700 W X 1

ACCESSORIES

• AV BIT IN - DIGITAL INTERFACE FOR ALL AV AMPLIFIERS. IT OFFERS ONE AD LINK AND AC LINK INPUT AS WELL AS ONE AD LINK AND AC LINK OUTPUT FOR A PERFECT DIGITAL CONNECTION WITH DIGITAL PROCESSORS (BIT ONE AND BIT TEN D) TO DRIVE A MULTI-AMPLIFIED SYSTEM.
• VCRA - REMOTE SUB VOLUME CONTROL - WHEN YOU DRIVE THE SUBWOOFER IN MONO, YOU CAN USE VCRA ANALOG REMOTE CONTROL BY CONNECTING THE EXTERNAL SUBWOOFER VOLUME TO THE SPECIAL SUB VOL SOCKET.

FEATURES

• DRC – DIGITAL REMOTE CONTROL
• THE DRC MOUNTED IN THE VEHICLE DASHBOARD PROVIDES ACCESS TO THE FUNCTIONS OF ALL THE THESIS AMPLIFIERS INSTALLED IN THE SYSTEM, ALL WITHIN YOUR IMMEDIATE GRASP. 
• PROVIDING SOURCE SELECTION BETWEEN ANALOG AND OPTICAL INPUTS, IT ALSO CONTROLS THE ESSENTIAL FUNCTIONS YOU NEED TO ACCESS FREQUENTLY

POWER OUTPUT

                                                   LOAD IMP   MONO           STEREO
DUAL POWER - HI-CURRENT 4 OHM        1000 W X 1    300 W X 2
                                                   2 OHM        1500 W X 1    500 W X 2
                                                   1 OHM                               750 W X 2
DUAL POWER - A CLASS         4 OHM                                80 W X 2

FEATURES

• DRC – DIGITAL REMOTE CONTROL
• THE DRC MOUNTED IN THE VEHICLE DASHBOARD PROVIDES ACCESS TO THE FUNCTIONS OF ALL THE THESIS AMPLIFIERS INSTALLED IN THE SYSTEM, ALL WITHIN YOUR IMMEDIATE GRASP.
• PROVIDING SOURCE SELECTION BETWEEN ANALOG AND OPTICAL INPUTS, IT ALSO CONTROLS THE ESSENTIAL FUNCTIONS YOU NEED TO ACCESS FREQUENTLY.

POWER OUTPUT

FEATURES

• DRC – DIGITAL REMOTE CONTROL
• THE DRC MOUNTED IN THE VEHICLE DASHBOARD PROVIDES ACCESS TO THE FUNCTIONS OF ALL THE THESIS AMPLIFIERS INSTALLED IN THE SYSTEM, ALL WITHIN YOUR IMMEDIATE GRASP. 
• PROVIDING SOURCE SELECTION BETWEEN ANALOG AND OPTICAL INPUTS, IT ALSO CONTROLS THE ESSENTIAL FUNCTIONS YOU NEED TO ACCESS FREQUENTLY.

SPECIFICATIONS

DUAL POWER - HI-CURRENT 4 OHM 850 W X 1
                                                   2 OHM 1500 W X 1
                                                   1 OHM 2300 W X 1
DUAL POWER - A CLASS        4 OHM 200 W X 1
AMP CHAIN                               2 OHM (2 AMP) 4500 W X 1

• 400 WATTS OF MAXIMUM POWER OUTPUT
• 50 WATTS × 4 CONTINUOUS @ 4-OHMS
• 75 WATTS × 4 CONTINUOUS @ 2-OHMS
• 150 WATTS × 2 CONTINUOUS @ 4-OHMS BRIDGED
• DOUBLE SIDE CONFORMAL COATED PCB ASSEMBLY
• MOS-FET POWER SUPPLY
• 12DB/OCT. HIGH PASS ELECTRONIC CROSSOVER. VARIABLE 15 - 250HZ (FR/RR)
• VARIABLE GAIN CONTROL
• TURN-ON/OFF MUTING CIRCUITRY (SOFT MUTE)
• GROUND LOOP ISOLATION INPUT CIRCUIT
• CORROSION RESISTANT NICKEL PLATED RCA, POWER, AND SPEAKER CONNECTIONS
• RCA AND HIGH LEVEL SPEAKER INPUTS

• 700 WATTS OF MAXIMUM POWER OUTPUT
• 50 WATTS × 4 + 200 WATTS × 1 CONTINUOUS @ 4-OHMS
• 75 WATTS × 4 + 300 WATTS × 1 CONTINUOUS @ 2-OHMS
• 150 WATTS × 2 CONTINUOUS @ 4-OHMS BRIDGED
• 4 LAYER CONFORMAL COATED PCB ASSEMBLY
• BASS BOOST ADJUSTMENT
• MOS-FET POWER SUPPLY
• 12DB/OCT. LOW/HIGH PASS ELECTRONIC CROSSOVER. VARIABLE 35-250HZ (SUB) / 15-250HZ (FR/RR)
• VARIABLE GAIN CONTROL
• TURN-ON/OFF MUTING CIRCUITRY (SOFT MUTE)
• GROUND LOOP ISOLATION INPUT CIRCUIT
• CORROSION RESISTANT NICKEL PLATED RCA, POWER, AND SPEAKER CONNECTIONS
• RCA AND HIGH LEVEL SPEAKER INPUTS

•  
• 1300 WATTS OF MAXIMUM MUSIC POWER
• 650 WATTS X 1 CONTINUOUS @ 2-OHMS
• 330 WATTS × 1 CONTINUOUS @ 4-OHMS
• ADJUSTABLE - 12DB/OCT. LOW PASS ELECTRONIC CROSSOVER, 50HZ-500HZ
• BASS EXTENDER CONTROL, 0-12DB AT 45HZ
• ADJUSTABLE INFRASONIC FILTER, 10-50HZ
• PHASE CONTROL, 0-180 DEGREES
• BC2 REMOTE SUBWOOFER LEVEL CONTROL INCLUDED
• SOFT TURN-ON AND TURN-OFF CIRCUITRY
• AUDIO PASS-THROUGH OUTPUTS FOR ADDITIONAL AMPLIFIERS
• CONFORMALLY COATED PC BOARD
• STAINLESS HARDWARE
• MOS-FET POWER SUPPLY
• GROUND LOOP ISOLATION CIRCUIT
• CORROSION RESISTANT NICKEL PLATED RCA, POWER, AND SPEAKER CONNECTIONS

• 350 WATTS OF MAXIMUM MUSIC POWER 
• 125 WATTS × 2 CONTINUOUS @ 2-OHMS 
• 85 WATTS × 2 CONTINUOUS @ 4-OHMS 
• CONFORMALLY COATED PC BOARD 
• STAINLESS HARDWARE 
• MOS-FET POWER SUPPLY 
• 12DB/OCT. HIGH/LOW PASS ELECTRONIC CROSSOVER, 50HZ-500HZ (×10, 500HZ – 5KHZ) 
• SOFT TURN-ON AND TURN-OFF CIRCUITRY 
• GROUND LOOP ISOLATION CIRCUIT 
• CORROSION RESISTANT NICKLE PLATED RCA, POWER, AND SPEAKER CONNECTIONS

• 600 WATTS OF MAXIMUM MUSIC POWER
• 125 WATTS × 4 CONTINUOUS @ 2-OHMS
• 85 WATTS × 4 CONTINUOUS @ 4-OHMS
• INDEPENDENT FRONT / REAR ADJUSTABLE - 12DB/OCT. HIGH/LOW PASS ELECTRONIC CROSSOVER, 50HZ-500HZ (×10,500HZ–5KHZ)
• INDEPENDENT FRONT/REAR BASS EXTENDER CONTROL
• BC2 REMOTE SUBWOOFER LEVEL CONTROL INCLUDED
• SOFT TURN-ON AND TURN-OFF CIRCUITRY
• SIGNAL SENSING REMOTE TURN-ON CIRCUIT
• CONFORMALLY COATED PC BOARD
• STAINLESS HARDWARE
• MOS-FET POWER SUPPLY
• GROUND LOOP ISOLATION CIRCUIT
• CORROSION RESISTANT NICKEL PLATED RCA, POWER, AND SPEAKER CONNECTIONS

• 1,000 WATTS OF MAXIMUM MUSIC POWER
• 125 WATTS × 6 CONTINUOUS @ 2-OHMS
• 85 WATTS × 6 CONTINUOUS @ 4-OHMS
• INDEPENDENT FRONT / REAR ADJUSTABLE - 12DB/OCT. HIGH/LOW PASS ELECTRONIC CROSSOVER, 50HZ-500HZ
• INDEPENDENT BASS EXTENDER CONTROL
• BC2 REMOTE SUBWOOFER LEVEL CONTROL INCLUDED
• SOFT TURN-ON AND TURN-OFF CIRCUITRY
• SIGNAL SENSING REMOTE TURN-ON CIRCUIT
• CONFORMALLY COATED PC BOARD
• STAINLESS HARDWARE
• MOS-FET POWER SUPPLY
• GROUND LOOP ISOLATION CIRCUIT
• CORROSION RESISTANT NICKEL PLATED RCA, POWER, AND SPEAKER CONNECTIONS