Subwoofers

SPECIFICATIONS

• BASKET: PRESSED STEEL
• CONE MATERIAL: PRESSED PAPER
• FREQUENCY RESPONSE: 26HZ - 1.5KHZ
• PEAK POWER (WATTS): 1000
• RATED POWER (WATTS): 250
• SENSITIVITY: (DB) 90
• SURROUND MATERIAL: BUTYL RUBBER
• VOICE COIL TYPE: ROUND WOUND COPPER

THIELE SMALL PARAMETERS

• COMPLIANCE (CMS) (?M/N): 152.00U M/N
• CONE AREA (SD) (CM²): 530.93
• CONE AREA (SD) (IN²): 82.29
• D.C. COIL RESISTANCE (RE) (?): 3.71 OHM
• ELECTRICAL Q (QES): 1.22
• FORCE FACTOR (BL) (TM): 9.63
• FREE AIR RESONANCE (FS): 34.40
• LINEAR EXCURSON (XMAX) (IN): 0.24
• LINEAR EXCURSON (XMAX) (MM): 6.00
• MECHANICAL EXCURSION (IN): 0.35
• MECHANICAL EXCURSION (MM): 9.00
• MECHANICAL Q (QMS): 9.23
• TOTAL LOUDSPEAKER Q (QTS): 1.08
• VAS (CUFT): 2.12
• VAS (L): 60.66
• VOICE COIL IMPEDANCE: 4 OHM

SPECIFICATIONS

• BASKET PRESSED STEEL
• CONE MATERIAL PRESSED PAPER
• CONE SIZE 10"
• FREQUENCY RESPONSE 38HZ - 1.5KHZ
• PEAK POWER (WATTS) 1400
• RATED POWER (WATTS) 350
• SENSITIVITY (DB) 87
• SURROUND MATERIAL BUTYL RUBBER

THIELE SMALL PARAMETERS

• COMPLIANCE (CMS) (?M/N) 107.00U M/N
• CONE AREA (SD) (CM²) 356.33
• CONE AREA (SD) (IN²) 55.23
• D.C. COIL RESISTANCE (RE) (?) 4.18 OHMS
• ELECTRICAL Q (QES) 0.84
• FORCE FACTOR (BL) (TM) 12.73
• FREE AIR RESONANCE (FS) 45.30
• LINEAR EXCURSON (XMAX) (IN) 0.24
• LINEAR EXCURSON (XMAX) (MM) 6.00
• MECHANICAL EXCURSION (IN) 0.35
• MECHANICAL EXCURSION (MM) 9.00
• MECHANICAL Q (QMS) 2.72
• TOTAL LOUDSPEAKER Q (QTS) 0.64
• VAS (CUFT) 0.07
• VAS (L) 19.31
• VOICE COIL IMPEDANCE 2 X 4 OHM

SPECIFICATIONS

• BASKET PRESSED STEEL
• CONE MATERIAL PRESSED PAPER
• FREQUENCY RESPONSE 30HZ - 1.2KHZ
• PEAK POWER (WATTS) 1600
• RATED POWER (WATTS) 400
• SENSITIVITY (DB) 89
• SURROUND MATERIAL BUTYL RUBBER

THIELE SMALL PARAMETERS

• COMPLIANCE (CMS) (?M/N) 112.00U M/N
• CONE AREA (SD) (CM²) 530.93
• CONE AREA (SD) (IN²) 82.29
• D.C. COIL RESISTANCE (RE) (?) 4.47 OHM
• ELECTRICAL Q (QES) 0.84
• FORCE FACTOR (BL) (TM) 14.04
• FREE AIR RESONANCE (FS) 38.30
• LINEAR EXCURSON (XMAX) (IN) 0.24
• LINEAR EXCURSON (XMAX) (MM) 6.00
• MECHANICAL EXCURSION (IN) 0.35
• MECHANICAL EXCURSION (MM) 9.00
• MECHANICAL Q (QMS) 2.93
• TOTAL LOUDSPEAKER Q (QTS) 0.65
• VAS (CUFT) 1.58
• VAS (L) 44.69
• VOICE COIL IMPEDANCE 2 X 2 OHM

• IMPEDANCE: 4Ω
• WOOFER SIZE: 30 CM
• WOOFER MATERIAL: MICA REINFORCED IMPP CONE
• VOICE COIL TYPE: COPPER
• VOICE COIL BOBBIN TYPE: POLYMIDE
• POLE YOKE TYPE: TRANSLATE5
• MAGNETS: STRONTIUM FERRITE
• TERMINALS: PUSH-TYPE
• RECOMMENDED SEALED ENCLOSURE: 22.7 LITRES
• WEIGHT: 5.92 KG
• MOUNTING DEPTH: 86,0 MM

• 4 SM4E ADAPTORS INCLUDED FOR OEM PLACEMENT OF MIDRANGE OR COAXIALS ON BMW X5 (F15) AND X6 (F16)
• 4 GM4E ADAPTORS INCLUDED FOR OEM PLACEMENT OF MIDRANGE OR COAXIALS ON BMW 5 SERIES SEDAN (G30) AND STATION WAGON (G31)
• MADE OF ABS AND EQUIPPED WITH SEALING GASKET AND FIXING SCREWS

FEATURES

• NEODYMIUM MAGNETIC GROUP - TO MAXIMIZE PERFORMANCE WHILE MINIMIZING BULK AND WEIGHT
• DEVELOPED WITH ELECTROACOUSTIC PARAMETERS CUSTOMIZED FOR BMW-MINI - TO INCREASE LISTENING ENGAGEMENT, THROUGH POWERFUL AND CRISP LOW FREQUENCIES, EXPLOITING THE ACOUSTIC LOAD PROVIDED BY THE FACTORY BOX
• 38 MM VOICE COIL WOUND ON ALUMINIUM SUPPORT - FOR A CONSIDERABLE POWER DISSIPATION AND STABILITY EVEN DURING HIGH EXCURSIONS
• TWO 5 MM GASKETS PROVIDED - FOR OEM PLACEMENTS
• 2 OHM CONFIGURATION FOR MAXIMUM OUTPUT - IN COMBINATION WITH AP 8.9 BIT IN ACTIVE MULTI-AMPLIFICATION

SPECIFICATIONS

• COMPONENT: WOOFER
• SIZE MM (IN.): 200 (8) 
• IMPEDANCE Ω: 2
• FREQUENCY RESPONSE HZ: 40 ÷ 500 
• MAGNET SIZE (D X D X H) MM (IN.): 48 (1.89) X 18 (0.71) X 7 (0.28)
• WEIGHT OF ONE SPEAKER KG (LB.): 1,21 (2.67)
• VOICE COIL Ø MM (IN.): 50 (2)

POWER HANDLING

• W PEAK: 300
• W CONTINUOUS: 150

FEATURES

• NEODYMIUM MAGNETIC GROUP - TO MAXIMIZE PERFORMANCE WHILE MINIMIZING BULK AND WEIGHT
• DEVELOPED WITH ELECTROACOUSTIC PARAMETERS CUSTOMIZED FOR BMW-MINI - TO INCREASE LISTENING ENGAGEMENT, THROUGH POWERFUL AND CRISP LOW FREQUENCIES, EXPLOITING THE ACOUSTIC LOAD PROVIDED BY THE FACTORY BOX
• 38 MM VOICE COIL WOUND ON ALUMINIUM SUPPORT - FOR A CONSIDERABLE POWER DISSIPATION AND STABILITY EVEN DURING HIGH EXCURSIONS
• TWO 5 MM GASKETS PROVIDED - FOR OEM PLACEMENTS
• 2 OHM CONFIGURATION FOR MAXIMUM OUTPUT - IN COMBINATION WITH AP 8.9 BIT IN ACTIVE MULTI-AMPLIFICATION

SPECIFICATIONS

• COMPONENT: WOOFER
• SIZE MM (IN.): 200 (8) 
• IMPEDANCE Ω: 4
• FREQUENCY RESPONSE HZ: 35 ÷ 500 
• MAGNET SIZE (D X D X H) MM (IN.): 48 (1.89) X 18 (0.71) X 7 (0.28)
• WEIGHT OF ONE SPEAKER KG (LB.): 1,21 (2.67)
• VOICE COIL Ø MM (IN.): 50 (2)

POWER HANDLING

• W PEAK: 300
• W CONTINUOUS: 150

• COMP: REFLEX SUB BOX
• SUBWOOFER SIZE MM (IN.): 250 (10)
• SUBWOOFER VOICE COIL Ø MM (IN.): 60 (2.36)
• OUTPUT POWER (RMS): 400 W CONTINUOUS POWER/800 W PEAK POWER
• IMPEDANCE Ω: 4 Ω + 4 Ω
• SUB BOX SIZE MM (IN.): 472 (18.58) X 334 (13.15) X 120 (4.72)
• MAGNET: HIGH DENSITY FLUX FERRITE
• CONE: WATER-REPELLENT PRESSED PAPER
• WEIGHT OF ONE COMPONENT: KG (LB) 8,63 (19.03)

FEATURES

• ULTRA-LOW PROFILE (3.11 IN. / 79 MM) FOR MAXIMUM INSTALLATION FLEXIBILITY
• DESIGNED TO DELIVER MAXIMUM PERFORMANCE IN A SEALED ENCLOSURE STARTING FROM 7.5 LT
• SPECIAL DESIGNED CONE-DUSTCAP-BASKET GEOMETRY WHICH GUARANTEES A LONG LINEAR EXCURSION CAPABILITY (ALMOST 9 MM, ONE-WAY) WHILE KEEPING THE MOUNTING DEPTH TO MINIMUM
• AIR VENTS ON THE BASKET UNDERNEATH THE SPIDER, ELIMINATING THE NEED FOR THE CENTRAL POLE VENT ALLOWING MOUNTING CLOSE TO REAR WALL OF ENCLOSURE
• MASSIVE MOTOR ASSEMBLY, OPTIMIZED WITH FEM (FINITE ELEMENT MODELING) FOR PERFECT CONTROL UNDER HIGH POWER, HIGH EXCURSION CONDITIONS
• WATER-REPELLENT TREATED PAPER 8 IN. CONE, FEATURING A PROFILE DEVELOPED WITH FEM SIMULATION AND OPTIMIZED WITH THE KLIPPEL SCAN VIBROMETER
• DUAL VOICE COIL DESIGN SPECIFICALLY DEVELOPED TO BE COMBINED WITH EITHER AP8.9 BIT (2 CH + 2 CH BRIDGED), AP5.9 BIT (SUB CH) OR AP4.9 BIT/AP4 D (2 CH BRIDGED) AMPLIFIERS
• STEEL MESH GRILLE AND PLASTIC GASKET INCLUDED

SPECIFICATIONS

• COMPONENT: DOUBLE COILS SUBWOOFER
• SIZE MM (IN.): 200 (8) 
• IMPEDANCE: 4 Ω + 4 Ω
• SENSITIVITY: 83.5 DB
• MAGNET: HIGH DENSITY FLUX FERRITE
• CONE: COTTON FIBRE PRESSED PAPER
• XMECH: 16,5 MM (0.65 IN.)

POWER HANDLING

• W PEAK: 250
• W CONTINUOS: 500

FEATURES

• ULTRA-LOW PROFILE (3.11 IN. / 79 MM) FOR MAXIMUM INSTALLATION FLEXIBILITY
• DESIGNED TO DELIVER MAXIMUM PERFORMANCE IN A REFLEX ENCLOSURE STARTING FROM 8.5 LT
• SPECIAL DESIGNED CONE-DUSTCAP-BASKET GEOMETRY WHICH GUARANTEES A LONG LINEAR EXCURSION CAPABILITY (ALMOST 9 MM, ONE-WAY) WHILE KEEPING THE MOUNTING DEPTH TO MINIMUM
• AIR VENTS ON THE BASKET UNDERNEATH THE SPIDER, ELIMINATING THE NEED FOR THE CENTRAL POLE VENT ALLOWING MOUNTING CLOSE TO REAR WALL OF ENCLOSURE
• MASSIVE MOTOR ASSEMBLY, OPTIMIZED WITH FEM (FINITE ELEMENT MODELING) FOR PERFECT CONTROL UNDER HIGH POWER, HIGH EXCURSION CONDITIONS
• WATER-REPELLENT TREATED PAPER 8 IN. CONE, FEATURING A PROFILE DEVELOPED WITH FEM SIMULATION AND OPTIMIZED WITH THE KLIPPEL SCAN VIBROMETER
• SPECIFICALLY DEVELOPED TO BE COMBINED WITH EITHER THE AUDISON AP8.9 BIT (2 CH BRIDGED) OR AP4.9 BIT /AP4 D (2 CH BRIDGED) AMPLIFIERS
• STEEL MESH GRILLE AND PLASTIC GASKET INCLUDED

SPECIFICATIONS

• COMPONENT: SINGLE COILS SUBWOOFER
• SIZE MM (IN.): 200 (8) 
• IMPEDANCE: 4 Ω
• SENSITIVITY: 84 DB
• MAGNET: HIGH DENSITY FLUX FERRITE
• CONE: COTTON FIBRE PRESSED PAPER
• XMECH: 16,5 MM (0.65 IN.)

POWER HANDLING

• W PEAK: 250
• W CONTINUOS: 500

FEATURES

• CABINET: HIGH DENSITY COMPOUND RESIN
• MOUNTING: METAL BRACKETS (PAIR)
• MOUNTING POSITION: BEHIND SEATS, ON PANELS, CARGO AREAS
• WEIGHT: APPROX 3.5 KG (INCLUDING ACCESSORIES)
• DIMENSIONS: 250 (W) X 265 (H) X 118 (D) MM

SPECIFICATIONS

• POWER AMPLIFIER
  • INPUT: HIGH (SPEAKER WIRES) OR LOW LEVEL (RCA)
  • INPUT LEVEL (AT MAX GAIN): RCA: 100MV + 100MV/20KΩ SPEAKER LINE: 2V + 2V/5KΩ
  • RMS POWER OUTPUT: 125 WATTS @ 14.4V 80HZ 2Ω
  • MAXIMUM OUTPUT: 250 WATTS
  • SENSITIVITY: 102DB
  • CONTROL: WIRED REMOTE CONTROLLER
  • CONTROL FEATURES: FREQUENCY (50 ~ 125 HZ) GAIN AND PHASE
  • POWER SOURCE: 14.4V DC (10.8 ~ 15.6V)
  • CURRENT: 8A MAX
  • GROUNDING: NEGATIVE
• INTEGRATED SUBWOOFER
  • SPEAKER: HIGH COMPLIANCE, ROLLED EDGE
  • CONE DIAMETER: 200MM (8-INCH)
  • MAX POWER: 250 WATTS
  • VOICE COIL: HEAT RESISTANT Ø35MM
  • MAGNET: 16 OZ (440G) STRONTIUM
  • FREQUENCY: 37 – 200HZ
  • OUTPUT IMPEDANCE: 2Ω+ 2

FEATURES

• MAX POWER HANDLING : 1.000 WATTS
• CONTINUOUS POWER HANDLING : 300 WATTS
• SINGLE 4-OHM HEAVY DUTY BLACK ALUMINIUM VOICE COIL
• ALUMINISED IPP DUST CAP
• REINFORCED SPP CONE
• NITRILE BUTADIENE RUBBER HIGH EXCURSION SURROUND
• HYPER EXTENDED REAR VENTED POLE PIECE
• LINEAR COTTON SPIDER WITH INTEGRATED TINSEL LEADS
• CUSTOM SHALLOW STAMPED STEEL POWDER COATED BASKET
• FREQUENCY RESPONSE : 40 - 1.000 HZ
• EFFICIENCY : 83 DB / W / M
• IMPEDANCE : 4-OHM
• OUTSIDE DIMENSION : 260 MM
• MOUNTING DEPTH : 89,5 MM

SPECIFICATIONS

• SUBWOOFER SIZE (MM): 250
• MAXIMUM POWER HANDLING (W): 1,000
• CONTINUOUS POWER HANDLING (W): 300
• IMPEDANCE (Ω): 4
• FREQUENCY RESPONSE (HZ): 40 ~1.000
• SPL (DB): 83

ENCLOSURE

• DESIGN STYLE: ULTRA COMPACT SEALED
• CONSTRUCTION MATERIAL: MEDIUM DENSITY FIBRE-BOARD
• EXTERNAL COVERING: BLACK CARPET WITH STITCHED CLARION LOGO
• VB (L): 9.4
• F3 (HZ): 58.61
• FB (HZ): 74.36
• DIMENSIONS (W × H × D) (MM): 400 X 290 X 140

ULTRA-COMPACT SEALED ENCLOSURE

• THE 10" 1.000W SUBWOOFER IS PRELOADED IN A COMPACT SEALED ENCLOSURE. CONSIDERING ITS DYNAMIC SOUND PERFORMANCE, YOU’LL BE AMAZED AT ITS SLIM, SPACE-SAVING DESIGN.

FEATURES

• ULTRA-COMPACT SLIM-LINE ENCLOSURE
• 25 CM / 10” SLIM-LINE 1,000 W SUBWOOFER
• 400 W MONO POWER AMPLIFIER
• MONO 12 AWG AMPLIFIER INSTALLATION KIT INCLUDED

WF2520 SUBWOOFER SPECIFICATIONS

• MAXIMUM POWER HANDLING : 1,000 WATTS
• CONTINUOUS POWER HANDLING : 300 WATTS
• SINGLE 4-OHM HEAVY DUTY BLACK ALUMINIUM VOICE COIL
• ALUMINISED IPP DUST CAP
• REINFORCED SPP CONE
• NITRILE BUTADIENE RUBBER HIGH EXCURSION SURROUND
• HYPER EXTENDED REAR VENTED POLE PIECE
• LINEAR COTTON SPIDER WITH INTEGRATED TINSEL LEADS
• CUSTOM SHALLOW STAMPED STEEL POWDER COATED BASKET
• FREQUENCY RESPONSE : 40 - 1,000 HZ
• EFFICIENCY : 83 DB / W / M
• IMPEDANCE : 4-OHM
• OUTSIDE DIMENSION : 271 MM
• MOUNTING DEPTH : 71 MM
• ENCLOSURE SIZE : 0.35 - 0.7 CU. FT. (SEALED), 0.6 CU. FT. (PORTED)

XC2110 AMPLIFIER SPECIFICATIONS

• 400 WATTS OF MAXIMUM POWER OUTPUT
• 200 WATTS × 1 CONTINUOUS @ 4-OHMS
• 300 WATTS × 1 CONTINUOUS @ 2-OHMS
• DOUBLE SIDE CONFORMAL COATED PCB ASSEMBLY
• MOS-FET POWER SUPPLY
• 12DB / OCT. VARIABLE LOW PASS ELECTRONIC CROSSOVER. 35 - 250 HZ
• VARIABLE GAIN CONTROL
• TURN-ON / OFF MUTING CIRCUITRY (SOFT MUTE)
• GROUND LOOP ISOLATION INPUT CIRCUIT
• CORROSION RESISTANT NICKEL PLATED RCA, POWER, AND SPEAKER CONNECTIONS
• RCA AND HIGH LEVEL SPEAKER INPUTS
• DIMENSIONS (W × H × D) : 202 MM X 39 MM X 82 MM

BWK1012 AMPLIFIER INSTALLATION KIT FEATURES

• 400 WATTS OF MAXIMUM POWER OUTPUT
• 200 WATTS × 1 CONTINUOUS @ 4-OHMS
• 300 WATTS × 1 CONTINUOUS @ 2-OHMS
• DOUBLE SIDE CONFORMAL COATED PCB ASSEMBLY
• MOS-FET POWER SUPPLY
• 12DB / OCT. VARIABLE LOW PASS ELECTRONIC CROSSOVER. 35 - 250 HZ
• VARIABLE GAIN CONTROL
• TURN-ON / OFF MUTING CIRCUITRY (SOFT MUTE)
• GROUND LOOP ISOLATION INPUT CIRCUIT
• CORROSION RESISTANT NICKEL PLATED RCA, POWER, AND SPEAKER CONNECTIONS
• RCA AND HIGH LEVEL SPEAKER INPUTS
• DIMENSIONS (W × H × D) : 202 MM X 39 MM X 82 MM

FEATURES

• MAX POWER HANDLING : 1,000 WATTS
• CONTINUOUS POWER HANDLING : 300 WATTS
• DUAL 4-OHM HEAVY DUTY VOICE COILS
• ALUMINISED IPP DUST CAP
• REINFORCED SPP CONE
• NITRILE BUTADIENE RUBBER HIGH EXCURSION SURROUND
• HYPER EXTENDED REAR VENTED POLE PIECE
• LINEAR COTTON SPIDER WITH INTEGRATED TINSEL LEADS
• CUSTOM SHALLOW STAMPED STEEL POWDER COATED BASKET
• FREQUENCY RESPONSE : 25-1,000 HZ
• EFFICIENCY : 86 DB/W/M
• IMPEDANCE : 2-OHM

SPECIFICATIONS

• SUBWOOFER SIZE (MM): 300
• MAXIMUM POWER HANDLING (W): 1,000
• CONTINUOUS POWER HANDLING (W): 300
• IMPEDANCE (Ω): 2
• FREQUENCY RESPONSE (HZ): 25 ~1.000
• SPL (DB): 86

• MAX POWER HANDLING : 1000 WATTS 
• CONTINUOUS POWER HANDLING : 300 WATTS
• SINGLE 4-OHM HEAVY DUTY BLACK ALUMINUM VOICE COILS
• ALUMINIZED IPP DUST CAP
• REINFORCED SPP CONE
• NITRILE BUTADIENE RUBBER HIGH EXCURSION SURROUND
• HYPER EXTENDED REAR VENTED POLE PIECE
• CUSTOM STAMPED STEEL POWDER COATED BASKET
• FREQUENCY RESPONSE : 25-1000 HZ
• EFFICIENCY : 88 DB/W/M
• IMPEDANCE : 4-OHM
• OUTSIDE DIMENSION : 12"
• MOUNTING DEPTH : 5-7/8"
• ENCLOSURE SIZE : 1.0 CU. FT. (SEALED), 1.50 CU. FT. (PORTED)

FEATURES

• EROM SURROUND
• HIGH-TEMP, 2.0”, VOICE COIL
• DOUBLE LAYER DEEP BASS, HIGH EXCURSION SPIDER SYSTEM
• UNIQUE GLASS FIBER AND NATURAL PULP CONE
• BACK PLATE COIL GAP VENTING
• EXTENDED POLE PIECE
• DD STAMPED STEEL BASKET

SPECIFICATIONS

• MODEL: 210D
• DRIVER SIZE: 10"
• WATTS RMS: 100 – 300
• PEAK POWER: 900
• VCD: 2
• IMPEDANCE: D4
• PISTON DIA: IN 8 ½
• FS: HZ 36.34
• QMS: 5.861
• QES: 0.7299
• QTS: 0.649
• VAS: LITERS 33.26
• XMECH: MM 64
• XMAX: MM 10
• FRAME OD: IN 10 1/8
• FRAME OD W/GASKET: IN 10 3/8
• MOUNTING DIAMETER: IN 9 3/16
• MOUNTING DEPTH: IN 4 15/16
• MOTOR DIAMETER: IN 5 ½
• MOTOR DEPTH: IN 2
• WOOFER DISPLACEMENT: CU FT 0.06
• SEALED ENCLOSURE: CU FT 0.4 - 0.8
• PORTED ENCLOSURE: CU FT 1.25 - 1.5
• SHIPPING WEIGHT: LBS 11

FEATURES

• EROM SURROUND
• HIGH-TEMP, 2.0”, VOICE COIL
• DOUBLE LAYER DEEP BASS, HIGH EXCURSION SPIDER SYSTEM
• UNIQUE GLASS FIBER AND NATURAL PULP CONE
• BACK PLATE COIL GAP VENTING
• EXTENDED POLE PIECE
• DD STAMPED STEEL BASKET

SPECIFICATIONS

• MODEL: 212
• DRIVER SIZE: 12"
• WATTS RMS: 100 – 300
• PEAK POWER: 900
• VCD: 2
• IMPEDANCE: D4
• PISTON DIA: IN 10
• FS: HZ 32.3
• QMS: 6.186
• QES: 0.770
• QTS: 0.685
• VAS LITERS:42.446
• XMECH: MM 64
• XMAX: MM 10
• FRAME OD: IN 12 ¼
• FRAME OD W/GASKET: IN 12 ½
• MOUNTING DIAMETER: IN 11 1/8
• MOUNTING DEPTH: IN 5 ½
• MOTOR DIAMETER: IN 5 ½
• MOTOR DEPTH: IN 2
• WOOFER DISPLACEMENT: CU FT 0.08
• SEALED ENCLOSURE: CU FT 0.5 - 1.0
• PORTED ENCLOSURE: CU FT 1.75 - 2.75
• SHIPPING WEIGHT: LBS 12

• CONE MATERIAL: PRESSED PAPER
• FREQUENCY RESPONSE: 28HZ-2KHZ
• IMPEDANCE: 4 OHM
• PEAK POWER: 800 WATTS
• RATED POWER: 200 WATTS
• SENSITIVITY: 88DB

• CONE MATERIAL: PRESSED PAPER
• FREQUENCY RESPONSE: 26HZ-1.5KHZ
• IMPEDANCE: 4 OHM
• PEAK POWER: 1000 WATTS
• RATED POWER: 250 WATTS
• SENSITIVITY: 90 DB

SPECIFICATIONS

• BASKET PRESSED STEEL
• CONE MATERIAL PRESSED PAPER
• FREQUENCY RESPONSE 30HZ - 1.2KHZ
• PEAK POWER (WATTS) 1600
• RATED POWER (WATTS) 400
• SENSITIVITY (DB) 89
• SURROUND MATERIAL BUTYL RUBBER

THIELE SMALL PARAMETERS

• COMPLIANCE (CMS) (?M/N) 112.00U M/N
• CONE AREA (SD) (CM²) 530.93
• CONE AREA (SD) (IN²) 82.29
• D.C. COIL RESISTANCE (RE) (?) 4.47 OHM
• ELECTRICAL Q (QES) 0.84
• FORCE FACTOR (BL) (TM) 14.04
• FREE AIR RESONANCE (FS) 38.30
• LINEAR EXCURSON (XMAX) (IN) 0.24
• LINEAR EXCURSON (XMAX) (MM) 6.00
• MECHANICAL EXCURSION (IN) 0.35
• MECHANICAL EXCURSION (MM) 9.00
• MECHANICAL Q (QMS) 2.93
• TOTAL LOUDSPEAKER Q (QTS) 0.65
• VAS (CUFT) 1.58
• VAS (L) 44.69
• VOICE COIL IMPEDANCE 2 X 4 OHM