Car Amplifiers & Processors

FEATURES

• 1,600 WATTS MAX POWER
• COMPACT DESIGN FOR VERSATILE INSTALLATION OPTIONS
• WIRED BASS BOOST REMOTE AND VARIABLE BASS CONTROL
• 1 Ω STABLE

GENERAL SPECIFICATIONS

• RCA INPUTS: MONO
• AMPLIFIER CLASS: CLASS-D
• HI-RES CERTIFIED: NO
• BRIDGEABLE: N/A
• WARRANTY: 1 YEAR
• SPEAKER LEVEL INPUT: YES
• FUSE RATING: 40A X 2
• BASS BOOST REMOTE: YES
• AUTOMATIC SIGNAL SENSING AND TURN-ON: YES
• HI-VOLT INPUT LEVEL CONTROL: 200 MV TO 6.5 V
• TERMINAL TYPE: BLOCK
• LOAD IMPEDANCE ALLOWANCE (OHMS): 1 TO 8
• PROTECTION CONTROL SYSTEM: YES
• DIMENSIONS: 252MM (W) X 60MM (H) X 215MM (D)

POWER

• CONTINUOUS POWER (RMS) OUTPUT @ 1Ω: 800W RMS X 1
• CONTINUOUS POWER (RMS) OUTPUT @ 2Ω: 500W RMS X 1
• CONTINUOUS POWER (RMS) OUTPUT @ 4Ω: 300W RMS X 1
• CONTINUOUS POWER (RMS) OUTPUT - BRIDGED @ 4Ω: N/A

AUDIO ADJUSTMENTS

• LOW-PASS CROSSOVER FREQUENCY: 40 HZ
• LOW-PASS SLOPE (DB/OCTAVE): -12DB
• HIGH-PASS CROSSOVER FREQUENCY: N/A
• BASS BOOST FREQUENCY: 50 HZ
• BASS BOOST LEVEL: 0 DB TO 18 DB

AUDIO SPECIFICATIONS

• FREQUENCY RESPONSE: 10 HZ TO 240 HZ
• TOTAL HARMONIC DISTORTION (THD): < 0.5% (100 HZ)
• SIGNAL-TO-NOISE (SN) RATIO: > 100 DB

• AMPLIFIER TYPE: CLASS-AB
• BASS BOOST @ 45HZ: 0 - +18DB
• DAMPING FACTOR: GREATER THAN 200
• FREQUENCY RESPONSE: 20HZ - 400HZ
• HIGH AND LOW PASS CROSSOVER: 12DB PER OCTAVE
• HIGH LEVEL INPUT RANGE: 1 VOLT TO 30 VOLTS
• LOW LEVEL INPUT RANGE: 0.35 VOLTS TO 10 VOLTS
• LOW PASS CROSS OVER RANGE: 50HZ - 400HZ
• MINIMUM LOAD IMPEDANCE: 2 OHM
• NUMBER OF CHANNELS: 1
• OPERATING VOLTAGE: 10.5 - 16 VOLTS
• POWER (WATTS): 1200
• POWER REQUIREMENTS: 12V DC (NEGATIVE GROUND)
• RECOMMENDED MINIMUM POWER/GROUND: 4 GAUGE (AWG) CABLE
• RMS POWER OUTPUT @ 14.4V 1% THD+N: 200W X 1 (@4 OHM)
• RMS POWER OUTPUT @ 14.4V 1% THD+N: 300W X 1 (@ 2 OHM)
• SIGNAL TO NOISE RATIO: >50DB
• SUBSONIC CROSSOVER RANGE: 10HZ - 40HZ
• SUBSONIC FILTER: 12DB PER OCTAVE

SPECIFICATIONS

• POWER (WATTS) 3200
• RMS POWER OUTPUT @ 14.4V 1% THD+N 500W X 1 (@ 4 OHM)
• RMS POWER OUTPUT @ 14.4V 1% THD+N 800W X 1 (@ 2 OHM)
• AMPLIFIER TYPE CLASS-D
• NUMBER OF CHANNELS 1
• FREQUENCY RESPONSE 10HZ - 250HZ
• SIGNAL TO NOISE RATIO >50DB
• HIGH AND LOW PASS CROSSOVER 12DB PER OCTAVE
• SUBSONIC FILTER 12DB PER OCTAVE
• LOW PASS CROSS OVER RANGE 50HZ - 250HZ
• SUBSONIC CROSSOVER RANGE 10HZ - 40HZ
• BASS BOOST @ 45HZ 0 - +18DB
• LOW LEVEL INPUT RANGE 0.35 VOLTS TO 10 VOLTS
• HIGH LEVEL INPUT RANGE 1 VOLT TO 30 VOLTS
• MINIMUM LOAD IMPEDANCE 2 OHM AND 4 OHM IN LINK MODE
• DAMPING FACTOR GREATER THAN 200
• POWER REQUIREMENTS 12V DC (NEGATIVE GROUND)
• OPERATING VOLTAGE 10.5 - 16 VOLTS
• RECOMMENDED MINIMUM POWER/GROUND 4 GAUGE (AWG) CABLE

DIMENSIONS

• LENGTH 306MM (12")
• WIDTH 200MM (7-7/8")
• HEIGHT 51MM (2")

• AMPLIFIER TYPE: CLASS-AB
• BASS BOOST @ 45HZ: 0 - +18DB
• CROSSOVER RANGE: 50HZ - 400HZ
• DAMPING FACTOR: GREATER THAN 200
• FREQUENCY RESPONSE: 20HZ - 20KHZ
• HIGH AND LOW PASS CROSSOVER: 12DB PER OCTAVE
• HIGH LEVEL INPUT RANGE: 1 VOLT TO 30 VOLTS
• LOW LEVEL INPUT RANGE: 0.35 VOLTS TO 10 VOLTS
• MINIMUM LOAD IMPEDANCE: 2 OHM STEREO AND 4 OHM BRIDGED
• NUMBER OF CHANNELS: 2
• OPERATING VOLTAGE: 10.5 - 16 VOLTS
• POWER (WATTS): 1200
• POWER REQUIREMENTS: 12V DC (NEGATIVE GROUND)
• RECOMMENDED MINIMUM POWER/GROUND: 4 GAUGE (AWG) CABLE
• RMS POWER OUTPUT @ 14.4V 1% THD+N: 90W X 2 (@ 2 OHM)
• RMS POWER OUTPUT @ 14.4V 1% THD+N: 180W X 1 (@4 OHM BRIDGED)
• RMS POWER OUTPUT @ 14.4V 1% THD+N: 65W X 2 (@ 4 OHM)
• SIGNAL TO NOISE RATIO: >50DB

GENERAL

• RCA INPUTS: 4-CH
• AMPLIFIER CLASS: CLASS AB
• HI-RES CERTIFIED: NO
• BRIDGEABLE: YES
• WARRANTY: 1 YEAR
• SPEAKER LEVEL INPUT: YES
• FUSE RATING: 25A X 2
• BASS BOOST REMOTE: NO
• AUTOMATIC SIGNAL SENSING AND TURN-ON: YES
• HI-VOLT INPUT LEVEL CONTROL: 0.3V TO 6.5V (RCA IN), 3.0V TO 26V (SP IN)
• TERMINAL TYPE: SCREW
• LOAD IMPEDANCE ALLOWANCE (OHMS): 2 TO 4
• PROTECTION CONTROL SYSTEM: YES
• DIMENSIONS: 356(W) X 60(H) X 215(D) MM

POWER

• CONTINUOUS POWER (RMS) OUTPUT @ 1Ω: N/A
• CONTINUOUS POWER (RMS) OUTPUT @ 2Ω: 95W X 4
• CONTINUOUS POWER (RMS) OUTPUT @ 4Ω: 60W X 4
• CONTINUOUS POWER (RMS) OUTPUT - BRIDGED @ 4Ω: 190W X 2

AUDIO ADJUSTMENTS

• LOW-PASS CROSSOVER FREQUENCY: 80 HZ
• LOW-PASS SLOPE (DB/OCTAVE): -12DB/OCT (A/B CH)
• HIGH-PASS CROSSOVER FREQUENCY: 40-500 HZ
• BASS BOOST FREQUENCY: 50HZ
• BASS BOOST LEVEL: 0/6/12DB

AUDIO SPECIFICATIONS

• FREQUENCY RESPONSE: 10HZ ~ 70KHZ (+0DB , -3DB)
• TOTAL HARMONIC DISTORTION (THD): <0.05% ( 10W, 1KHZ)
• SIGNAL-TO-NOISE (SN) RATIO: > 95DB

• 1,000 WATTS OF MAXIMUM MUSIC POWER
• 125 WATTS × 6 CONTINUOUS @ 2-OHMS
• 85 WATTS × 6 CONTINUOUS @ 4-OHMS
• INDEPENDENT FRONT / REAR ADJUSTABLE - 12DB/OCT. HIGH/LOW PASS ELECTRONIC CROSSOVER, 50HZ-500HZ
• INDEPENDENT BASS EXTENDER CONTROL
• BC2 REMOTE SUBWOOFER LEVEL CONTROL INCLUDED
• SOFT TURN-ON AND TURN-OFF CIRCUITRY
• SIGNAL SENSING REMOTE TURN-ON CIRCUIT
• CONFORMALLY COATED PC BOARD
• STAINLESS HARDWARE
• MOS-FET POWER SUPPLY
• GROUND LOOP ISOLATION CIRCUIT
• CORROSION RESISTANT NICKEL PLATED RCA, POWER, AND SPEAKER CONNECTIONS

• POWERFUL FULL RANGE AMPLIFIER - DESIGNED TO DELIVER THE FULL AUDIO FREQUENCY, PERFECT FOR SPEAKER OR SUBWOOFER AMPLIFICATION
• 4-WAY CIRCUITRY PROTECTION - THERMAL / CURRENT OVERLOAD / DC OFFSET AND SHORT CIRCUIT PROTECTION ENSURES SUSTAINED OPERATION
• EMBEDDED LED INDICATORS FOR WARNING NOTIFICATIONS
• DIE CAST TERMINALS / NICKEL PLATED RCA JACKS - ENSURES ACCURATE SIGNAL TRANSFER FOR IMPROVED AUDIO REPRODUCTION
• VARIABLE INPUT GAIN CONTROL - ALLOWS FOR ADJUSTMENT OF THE INCOMING SIGNAL TO MATCH THE CONNECTED FUSION STEREO OR ANY OTHER AMPLIFIERS IN YOUR SYSTEM
• 2-OHM STABLE STEREO - INCREASED POWER OUTPUT AT LOWER IMPEDANCE

• AMPLIFIER TYPE: CLASS-D
• BASS BOOST @ 45HZ: 0 - +18DB
• DAMPING FACTOR: GREATER THAN 200
• FREQUENCY RESPONSE: 10HZ - 250HZ
• HIGH AND LOW PASS CROSSOVER: 12DB PER OCTAVE
• HIGH LEVEL INPUT RANGE: 1 VOLT TO 30 VOLTS
• LOW LEVEL INPUT RANGE: 0.35 VOLTS TO 10 VOLTS
• LOW PASS CROSS OVER RANGE: 50HZ - 250HZ
• MINIMUM LOAD IMPEDANCE: 2 OHM
• NUMBER OF CHANNELS: 1
• OPERATING VOLTAGE: 10.5 - 16 VOLTS
• POWER (WATTS): 1600
• POWER REQUIREMENTS: 12V DC (NEGATIVE GROUND)
• RECOMMENDED MINIMUM POWER/GROUND: 4 GAUGE (AWG) CABLE
• RMS POWER OUTPUT @ 14.4V: 1% THD+N 250W X 1 (@4 OHM)
• RMS POWER OUTPUT @ 14.4V: 1% THD+N 400 X 1 (@ 2 OHM)
• SIGNAL TO NOISE RATIO: >50DB
• SUBSONIC CROSSOVER RANGE: 10HZ - 40HZ
• SUBSONIC FILTER: 12DB PER OCTAVE

• MAXIMUM OUTPUT POWER: 1200W
• RMS POWER AT 4OHMS: 100W X 4CH
• RMS POWER AT 2OHMS: 130W X 4CH
• BRIDGED AT 4OHMS: 270W X 2CH
• FREQUENCY RESPONSE: 20HZ - 20KHZ
• HIGH PASS FILTER: 50HZ - 200HZ, -12DB/OCT
• LOW PASS FILTER: 50HZ - 200HZ, -12DB/OCT
• SPEAKER LEVEL INPUT: YES
• SIGNAL TO NOISE RATIO: 100DB
• DIMENSIONS: W X D X H (MM) 324 X 187 X 55

• NUMBER OF CHANNELS: 1 - MONOBLOCK
• MINIMUM IMPEDANCE UNBRIDGED: 2 OHM
• MINIMUM IMPEDANCE BRIDGED: NOT BRIDGEABLE
• BASS/GAIN REMOTE: NOT INCLUDED
• SPEAKER LEVEL INPUTS: YES
• MAXIMUM INPUT GAUGE SIZE: 4 GAUGE
• AMPLIFIER CLASS: D
• SERIES: PERFORMANCE (KENWOOD)
• BUILT-IN CROSSOVER: LOW PASS (LP)
• BRAND: KENWOOD
• COMBINED RMS POWER OUTPUT: 1000 RMS
• COMBINED PEAK POWER OUTPUT: 2000W
• DIMENSIONS:335 X 56 X 192
• RMS OUTPUT @ 4 OHMS : 500W X 1
• RMS OUTPUT @ 2 OHMS : 1000W X 1

• HIGH-LEVEL INPUT CAPABLE WITH AUTO TURN-ON CIRCUIT
• RCA PASS-THRU OUTPUTS
• FEATURES C.L.E.A.N. SET-UP
• OPTIONAL REMOTE PUNCH LEVEL CONTROL (PLC2) READY (W/ INPUT CLIP INDICATOR)
• 12DB/OCTAVE BUTTERWORTH CROSSOVER
• ON-BOARD PUNCH EQ WITH +18DB BOOST @ 45HZ
• MUTED TURN ON
• STEALTH TOP MOUNTED CONTROL PANEL
• CAST ALUMINIUM HEATSINK
• SHORT CIRCUIT PROTECTION
• OVERCURRENT PROTECTION

FEATURES

• REMOTE WIRED BASS/TREBLE BOOST
• 0DB TO +18DB BASS BOOST @ 45 HZ
• 0DB TO +12DB TREBLE BOOST @ 12.5 KHZ
• BASS/TREBLE FILTERING BASED UPON IN-BOARD AMPLIFIER CROSSOVER SETTING (HP-LP-AP)
• CONTROLS BASS ON REAR OUTPUTS OF 4-CHANNEL AMPLIFIERS
• CONVENIENTLY MOUNT UNDER DASH, INSIDE CENTER CONSOLE OR GLOVEBOX
• INCLUDES BASS KNOB, CABLE, MOUNTING CLIP, MOUNTING SCREWS
• 1 YEAR WARRANTY

COMPATIBLE MODELS

2012-2014

• PUNCH PBR300X2
• PUNCH PBR500X1

2011-2014

• PUNCH PBR300X1
• POWER T800-4AD
• POWER T1000-4AD

2011-2012

• PUNCH P1000X1D
• PUNCH P1000X5D

2010-2014

• POWER T500-1BDCP
• POWER T1000-1BDCP
• POWER T1500-1BDCP
• POWER T2500-1BDCP

2010-2012

• PUNCH P400-1
• PUNCH P500-4
• PUNCH P700-1BD

2009-2012

• PUNCH P300-2
• PUNCH P500-1BD

2009-2010

• POWER T1000-4

2009

• POWER T1000-1BD
• POWER T2500-1BD

2007-2014

• POWER T400-2
• POWER T400-4
• POWER T600-2
• POWER T600-4

2007-2012

• PUNCH P200-2
• PUNCH P300-1
• PUNCH P400-2
• PUNCH P400-4
• PUNCH P500-2
• PUNCH P1000-1BD

2007-2009

• POWER T500-1BD
• POWER T1500-1BD

FEATURES

• REMOTE WIRED LEVEL CONTROL
• WORKS IN CONJUNCTION WITH ON-BOARD GAIN CONTROL
• DUAL FUNCTION LED (POWER/CLIPPING)
• CONTROLS LEVEL WHEN CROSSOVER SET TO LP (LOW-PASS)
• CONTROLS LEVEL ON REAR OUTPUTS OF 4-CHANNEL AMPLIFIERS
• CONVENIENTLY MOUNT UNDER DASH, INSIDE CENTER CONSOLE OR GLOVEBOX
• INCLUDES BASS KNOB, CABLE, MOUNTING CLIP, MOUNTING SCREWS
• 1 YEAR WARRANTY

COMPATIBLE MODELS

2017

• DSR1

2016

• POWER T750X1BD / TM750X1BD
• POWER T1000X5AD / TM1000X5AD

2014-2016

• POWER T400X2AD / TM400X2
• POWER T500X1BR / TM500X1BR

2013-2016

• PUNCH P300X1 / PM300X1
• PUNCH P300X2 / PM300X2
• PUNCH P400X1 
• PUNCH P400X2 / PM400X2
• PUNCH P500X1BD / PM500X1BD
• PUNCH P500X2 / PM500X2
• PUNCH P600X4 / PM600X4
• PUNCH P1000X1BD / PM1000X1BD
• PUNCH P1000X2 
• PUNCH P1000X5 / PM1000X5

• OFC (OXYGEN FREE COPPER) FOR CORROSION RESISTANCE
• PLATINUM PLATED ENDS FOR CORROSION RESISTANCE
• FEMALE RCA JACKS
• 1 YEAR WARRANTY

• QUICK RELEASE PLUG ALLOWS FAST SAFE REMOVAL OF YOUR ACTIVE SUB BOXES AND OR EXPENSIVE AMPLIFERS AND POWERED AUDIO EQUIPMENT.
• FAST INSTALLATION NO SPECIAL TOOLS REQUIRED.
• UNIVERSAL - WORKS WITH ANY AMPLIFER OR ACTIVE SUB BOX.
• 80 AMP POWER RATING
• HEAVY DUTY GOLD PLATED TERMINALS ACCEPT UP TO 8 GAUGE WIRE
• BLACK ABS CONSTRUCTION FOR MAXIUM DURABILITY
• SCREW MOUNTABLE
• LARGE BOLTS TO SECURE OVERSIZED WIRE (ALLEN KEY INCLUDED)

POWER OUTPUT

• LOAD IMP.: 5 CHANNELS
• 4 OHM: 75 W X 2 + 140 W X 2 + 600 W X 1
• 4/2 OHM: 75 W X 2 + 140 W X 2 + 1000 W X 1
• 2/4 OHM: 75 W X 2 + 250 W X 2 + 1000 W X 1

ACCESSORIES

• AV BIT IN - DIGITAL INTERFACE FOR ALL AV AMPLIFIERS. IT OFFERS ONE AD LINK AND AC LINK INPUT AS WELL AS ONE AD LINK AND AC LINK OUTPUT FOR A PERFECT DIGITAL CONNECTION WITH DIGITAL PROCESSORS (BIT ONE AND BIT TEN D) TO DRIVE A MULTI-AMPLIFIED SYSTEM. 
• VCRA – REMOTE SUB VOLUME CONTROL - ANALOG REMOTE VOLUME CONTROL TO DRIVE THE SUBWOOFER IN MONO, BY CONNECTING THE EXTERNAL SUBWOOFER VOLUME TO THE SPECIAL SUB VOLUME SOCKET (ONLY WITH ANALOG INPUTS).

• DISTORTION THD - 0.03%
• BANDWIDTH - 5/20K HZ
• S/N RATIO (A WEIGHTED @ 1V) - 98DB
• DIGITAL RESOLUTION - 24 BIT/192 KHZ
• INPUT/OUTPUT - AD LINK / AC LINK

POWER OUTPUT

• LOAD IMP.: STEREO MONO
• 4 OHM: 260 W X 2 900 W X 1
• 2 OHM: 450 W X 2

ACCESSORIES

• AV BIT IN - DIGITAL INTERFACE FOR ALL AV AMPLIFIERS. IT OFFERS ONE AD LINK AND AC LINK INPUT AS WELL AS ONE AD LINK AND AC LINK OUTPUT FOR A PERFECT DIGITAL CONNECTION WITH DIGITAL PROCESSORS (BIT ONE AND BIT TEN D) TO DRIVE A MULTI-AMPLIFIED SYSTEM. 
• VCRA – REMOTE SUB VOLUME CONTROL - ANALOG REMOTE VOLUME CONTROL TO DRIVE THE SUBWOOFER IN MONO, BY CONNECTING THE EXTERNAL SUBWOOFER VOLUME TO THE SPECIAL SUB VOLUME SOCKET (ONLY WITH ANALOG INPUTS).

POWER SUPPLY

• POWER SUPPLY VOLTAGE: 11 ÷ 15 VDC
• IDLING CURRENT: 1.8 A
• IDLING CURRENT WHEN OFF: 0.02 MA
• CONSUMPTION @ 14.4 VDC (MAX MUSICAL POWER): 55 A

AMPLIFIER STAGE

• DISTORTION - THD (1KHZ @ 4Ω): 0.04 %
• BANDWIDTH (-3 DB): 4 ÷ 60K HZ
• S/N RATIO (A WEIGHTED @ 1V): 100 DBA
• DAMPING FACTOR (1K HZ @ 4Ω): 100
• INPUT SENSITIVITY: 0.3 ÷ 5 V RMS
• INPUT IMPEDANCE: 15K Ω
• SPEAKER-IN SENSITIVITY: 1.4 ÷ 24 V RMS
• SPEAKER-IN IMPEDANCE: 5K Ω
• MINIMUM LOAD IMPEDANCE: 2Ω
• NOMINAL POWER (RMS) @ 12 VDC, THD 0.3%, 4Ω:100 W

OUTPUT POWER (RMS) @ 14.4 VDC, THD 1%

• 4 CH: 120 W X 4 (4Ω)
• 4 CH: 200 W X 4 (2Ω)
• 4 CH: 120 W X 2 (4Ω) + 200 W X 2 (2Ω)
• 3 CH: 120 W X 2 (4Ω) + 400 W X 1 (4Ω)
• 3 CH: 200 W X 2 (2Ω) + 400 W X 1 (4Ω)
• 2 CH: 400 W X 1 (4Ω) + 400 W X 1 (4Ω)

CEA SPECIFICATIONS

• OUTPUT POWER @ 4Ω, 1% THD+N, 14.4 V: 120 W X 4 CH
• SN RATIO (REF. 1 W OUTPUT): 80 DBA

SIGNAL INPUTS / FILTERS

• INPUTS: PRE IN / SPEAKERS IN
• OUTPUTS: PRE OUT FULL RANGE
• A CH & B CH FILTERS (FULL / HI-PASS / LO-PASS): 50 ÷ 50K HZ (2 RANGE) @ 12 DB/OCT.
• B CH FILTER (LO-PASS 24 DB MONO): 50 ÷ 500 HZ @ 24 DB/OCT.

OTHER FUNCTIONS

• REMOTE IN: 7 ÷ 15 VDC - 1MA
• REMOTE OUT: 12 VDC - 50MA
• FUSE (STRIP TYPE): 60 A
• REMOTE SUB VOLUME ADJ. (B CH LO-PASS 24 DB): (-50 ÷ 6) DB
• SPEAKERS IN TURN-ON (ART): SELECTABLE

SIZE / WEIGHT

• MAX SIZE (MM/INCHES): 220 X 470 X 58 / 8,66” X 18,50” X 2,28”
• WEIGHT (KG/LB): 7.2 / 15.87

ACCESSORIES

• AV BIT IN HD - DIGITAL INTERFACE FOR ALL AV AMPLIFIERS, FOR PERFECT DIGITAL CONNECTION WITH AUDISON BIT PROCESSORS PROVIDED WITH AD LINK AND AC LINK CONNECTIONS. BY MOUNTING THE AV BIT IN “DIGITAL INTERFACE” ONTO THE VOCE AMPLIFIER SERIES, THROUGH THE AD LINK CONNECTION THE S/PDIF DIGITAL SIGNAL WILL GET DIRECTLY TO THE HIGH QUALITY INTERNAL D/A CONVERTERS. AFTER THESE, THE SIGNAL BECOMES ANALOG AND IS IMMEDIATELY AMPLIFIED PREVENTING IT FROM DETERIORATION DUE TO THE LONG PATHS. THE RESULT IS EXTREMELY HIGH QUALITY MUSIC, NOT ACHIEVABLE WITH ANY OTHER ANALOG SYSTEM. IT OFFERS ONE AD LINK AND AC LINK INPUT, AS WELL AS ONE AD LINK AND AC LINK OUTPUT IN ORDER TO DRIVE A MULTI-AMPLIFIED SYSTEM. THANKS TO ITS DIGITAL PANEL WITH 3 CHARACTER DISPLAY AND 4 PUSH BUTTONS, YOU CAN SELECT THE AMPLIFIER TYPE, MONO OR STEREO MODE, AND ALSO THE DIGITAL CHANNEL COMING FROM THE AUDIO PROCESSOR. AV BIT IN HD FEATURES TWO NEW SWITCHES ON THE FRONT PANEL: ONE PROVIDES YOU WITH THE ABILITY OF TURNING OFF THE GAIN CONTROL OF THE AMPLIFIER TO ACHIEVE AN IMPROVED SIGNAL TO NOISE RATIO. WITH THE SECOND SWITCH YOU CAN CONTROL THE DSP REMOTE START FUNCTION. CONNECTION TO AMPLIFIER: REMOVE ANALOG CROSSOVER MODULE AND INSERT AV BIT IN MODULE INTO THE AMPLIFIER’S FRONT SIDE. IT REQUIRES NO EXTERNAL POWER SUPPLY.
• VCRA – REMOTE SUB VOLUME CONTROL - WHEN YOU DRIVE THE SUBWOOFER IN MONO, YOU CAN USE VCRA ANALOG REMOTE CONTROL BY CONNECTING THE EXTERNAL SUBWOOFER VOLUME TO THE SPECIAL SUB VOL SOCKET.

POWER OUTPUT

• LOAD IMP.: MONO
• 4 OHM: 700 W X 1
• 2 OHM: 1300 W X 1
• 1 OHM: 1700 W X 1

ACCESSORIES

• AV BIT IN - DIGITAL INTERFACE FOR ALL AV AMPLIFIERS. IT OFFERS ONE AD LINK AND AC LINK INPUT AS WELL AS ONE AD LINK AND AC LINK OUTPUT FOR A PERFECT DIGITAL CONNECTION WITH DIGITAL PROCESSORS (BIT ONE AND BIT TEN D) TO DRIVE A MULTI-AMPLIFIED SYSTEM.
• VCRA - REMOTE SUB VOLUME CONTROL - WHEN YOU DRIVE THE SUBWOOFER IN MONO, YOU CAN USE VCRA ANALOG REMOTE CONTROL BY CONNECTING THE EXTERNAL SUBWOOFER VOLUME TO THE SPECIAL SUB VOL SOCKET.

FEATURES

• BIT DRIVE - AUTO TUNING BY AUDISON BIT TUNE AND COMMUNICATION WITH BIT DRIVE PORTAL.
• DE-EQ - DE-EQUALIZATION FUNCTION TO “FLATTEN” ANY EQUALIZATION APPLIED BY DEFAULT BY OEM SOURCES.
• USS TECHNOLOGY - USS TECHNOLOGY ALLOWS BIT PROCESSORS TO WORK WITH HEADUNITS FEATURING THE “SPEAKER LOAD DETECTION” CIRCUIT
• IDATALINK MAESTRO AR COMPATIBILITY - WHEN BIT NOVE IS INSTALLED INTO A COMPATIBLE VEHICLE USING THE IDATALINK MAESTRO AR (SOLD SEPARATELY), THE USER CAN ENJOY A PERFECT INTEGRATION WITH FACTORY INSTALLED NAVIGATION, ADVANCED SAFETY SYSTEMS, VOICE-CONTROLLED HANDS-FREE AND INFOTAINMENT. (ONLY FOR NORTH AMERICA).

SPECIFICATIONS

• ANALOG INPUTS: 6 HIGH LEV. + 6 PRE IN
• DIGITAL INPUTS: 2
• ANALOG OUTPUTS: 9
• DIGITAL OUTPUTS: NOT AVAILABLE
• EQUALIZERS FOR EACH OUTPUTS: PARAMETRICS EQUALIZERS: ±12 DB;10 POLE;
• CROSSOVER FILTER TYPE: FULL / HI-PASS / LOW PASS / BAND PASS
• FILTER MODE AND SLOPE: LINKWITZ @ 12 / 24; BUTTERWORTH @ 6 / 12 / 18 / 24

ACCESSORIES

• DRC MP - THE NEW AUDISON DRC MP (DIGITAL REMOTE CONTROL MULTIMEDIA PLAY) IS COMPATIBLE WITH ALL THE AUDISON ELECTRONICS FEATURING AC LINK BUS. ITS SLIM PROFILE ALONG WITH THE HOLDER SUPPLIED WITH IT EASES THE INSTALLATION IN THE BEST POSITION INSIDE THE CAR. THANKS TO THE NEW JOYSTICK, “RUBBER TOUCH” FINISHED FOR BEST CONTROL OF THE MOVEMENTS ALONG THE FOUR DIRECTION AXES, THE “DRC SETTINGS” MENU CAN BE ADJUSTED AND NAVIGATION IS ALSO POSSIBLE THROUGH THE “NAVI COMMAND” FUNCTION IF THE SYSTEM FEATURES AN AUDISON BIT PLAY HD WITH VIDEO OUTPUT CONNECTED TO A MONITOR.
• DRC AB - DRC AB ENABLES THE MAIN SYSTEM CONTROL (VOLUME, BALANCE, FADER AND SUBWOOFER VOLUME, BASS-BOOST) WITHOUT THE USE OF A PC. THANKS TO THIS DEVICE, INSTALLED IN AN ERGONOMIC POSITION WITHIN THE CAR DASHBOARD, THE USER CAN: CHOOSE BETWEEN THE FOUR DSP PRESETS AND SELECT THE SOURCE AMONG MASTER, AUXILIARY AND THE TWO OPTICAL DIGITAL INPUTS.
• ECK DRC - IT IS A KIT COMPOSED OF A CABLE AND AN ADAPTER ALLOWING A 2 M / 78.74 IN. ADDITIONAL EXTENSION OF THE CABLE SUPPLIED WITH THE DRC. THIS EXTENSION IS REQUIRED FOR INSTALLATIONS ON ESPECIALLY LONG VEHICLES SUCH AS SUV’S. TOTAL LENGTH OF THE SUPPLIED CABLE WITH THE EXTENSION IS EQUAL TO 6,5 M / 225.90 IN. PACKAGE: POLYBAG – QTY. 1
• SPM 4 - STEREO PASSIVE MIXER (UNPOWERED) FEATURING 4 INPUT CHANNELS AND 2 OUTPUT CHANNELS, DESIGNED FOR ACTIVE OEM MULTI-WAY SYSTEMS WHERE EACH SPEAKER IS POWERED BY ONE SPECIFIC AMPLIFIED CHANNEL. SPM4 MIXES AUDIO THROUGH 4 AUDIO TRANSFORMERS SPECIFICALLY DEVELOPED TO ACHIEVE VERY LOW DISTORTION AND HIGHLY LINEAR ACOUSTIC RESPONSE. SPM4 PROVIDES THE ABILITY TO MIX THE MIDRANGE/WOOFER AND TWEETER CHANNELS COMING FROM THE AMPLIFIER AND SUPPLY ONE SINGLE MID-HIGH CHANNEL. THE CH1(L/R) CHANNELS FEATURE TWO INPUTS, ONE FEATURES AN INVERTING INPUT COMPARED TO CH2 (L/R) CHANNELS; THE MIXING PROCESS OFTEN GIVES BETTER RESULTS WHEN ONE OF THE TWO CHANNELS UNDERGOES A 180° DEPHASING. SPM4 IS ESPECIALLY RECOMMENDED TO EXTEND THE NUMBER OF INPUTS OF THE AUDISON DIGITAL PROCESSORS OR AMPLIFIERS WITH BUILT-IN DSP BECAUSE THEY FEATURE A DE-EQUALIZER (DE-EQ). IN THAT CASE, ANY POSSIBLE NON-LINEAR ACOUSTIC EMISSIONS DUE TO THE MIXING OF THE PRE-EXISTING FILTERED CHANNELS ARE DULY COMPENSATED.
• ES3 - IT PREVENTS THE PROCESSOR FROM SHUTTING DOWN WHEN TURNING ON VEHICLES FEATURING THE START & STOP SYSTEM. WHEN STARTING THE ENGINE, THE VEHICLE BATTERY VOLTAGE MIGHT DECREASE BELOW 8 VOLTS VALUE. IF AN AUDISON BIT PROCESSOR IS INSTALLED IN YOUR SYSTEM, ESPECIALLY WITH VEHICLES FEATURING THE START & STOP SYSTEM, LOW SUPPLY VOLTAGE VALUES MIGHT MAKE THE PROCESSOR SHUT DOWN. IN ORDER TO AVOID WAITING FOR THE PROCESSOR TO COMPLETE ITS TURN-ON CYCLE AGAIN, YOU CAN INSTALL THE ES3 BY CONNECTING IT IN SERIES TO THE PROCESSOR POWER SUPPLY CABLES.
• STR - MALE-FEMALE TOSLINK ADAPTER WITH ROTATING HEAD. 90° ANGLE SHAPE TO SAVE SPACE. PACKAGE: POLYBAG QTY. 1
• STA - OPTICAL ADAPTER TO EXTEND OPTICAL CABLES FEATURING TOSLINK CONNECTORS. PACKAGE: POLYBAG – QTY. 1
• PIC 6 - RCA CONNECTOR FOR EFFORTLESS AND FAST CONNECTIONS BETWEEN THE HEAD UNIT PRE OUTS (1,2 MIN.) AND THE BIT NOVE PRE INPUTS. PACKAGE: CARTON BOX – QTY. 1
• OP 4.5 - OPTICAL DIGITAL AUDIO SIGNAL CABLE, DESIGNED FOR CAR AUDIO APPLICATIONS, ALLOWING THE TRANSFER OF THE OPTICAL SIGNAL WITHOUT SIGNAL LOSS. AN ESPECIALLY THICKER SHEATH PROTECTS THE OPTICAL FIBRE TO PREVENT THE CABLE FROM DAMAGES IF IT IS PRESSED AGAINST SHARP EDGES. THE METAL CONNECTOR PROTECTS THE OPTICAL FIBRE ALONG ITS FULL LENGTH, ENSURING A STABLE TRANSMISSION OF THE SIGNAL ALSO IN THE EVENT OF STRONG VIBRATIONS. ENDING WITH TOSLINK CONNECTORS FOR S/PDIF DIGITAL AUDIO SIGNALS. CABLE LENGTH 4,5 M/177,16” PACKAGE: POLYBAG QTY. 1
• OP 1.5 - OPTICAL DIGITAL AUDIO SIGNAL CABLE, DESIGNED FOR CAR AUDIO APPLICATIONS, ALLOWING THE TRANSFER OF THE OPTICAL SIGNAL WITHOUT SIGNAL LOSS. AN ESPECIALLY THICKER SHEATH PROTECTS THE OPTICAL FIBRE TO PREVENT THE CABLE FROM DAMAGES IF IT IS PRESSED AGAINST SHARP EDGES. THE METAL CONNECTOR PROTECTS THE OPTICAL FIBRE ALONG ITS FULL LENGTH, ENSURING A STABLE TRANSMISSION OF THE SIGNAL ALSO IN THE EVENT OF STRONG VIBRATIONS. ENDING WITH TOSLINK CONNECTORS FOR S/PDIF DIGITAL AUDIO SIGNALS.
• CABLE LENGTH 4,5 M/177,16”
• PACKAGE: POLYBAG QTY. 1

ACCESSORIES

• DRC – DIGITAL REMOTE CONTROL
• DRC IS THE DIGITAL INTERFACE BETWEEN THE BIT PROCESSORS AND THE USER.
• DRC MOUNTED IN THE VEHICLE DASHBOARD WITH BIT TEN PROCESSOR, PROVIDES:
• - ABILITY TO SELECT BETWEEN MAIN AND AUX INPUTS
• - CONTROL OF MASTER VOLUME, SUBWOOFER VOLUME, BALANCE AND FADER
• - ABILITY TO CHOOSE BETWEEN 2 USER-DEFINED MEMORY PRESETS FOR EQUALIZER, CROSSOVER AND TIME ALIGNMENT SETTINGS.
• ECK DRC - DRC CABLE EXTENSION KIT, FOR INSTALLATIONS ON ESPECIALLY LONG VEHICLES.
• RCA ADAPTER CABLE - ESSENTIAL CONNECTOR MAKING LINK FAST AND EFFORTLESS. IT EXPEDITES CONNECTIONS BETWEEN THE HEAD UNIT PRE OUTS (2 V MIN.) AND THE BIT TEN HI-LEVEL INPUTS.