Wiring Wizard

• AMPLIFIER TYPE: CLASS-D
• BASS BOOST @ 45HZ: 0 - +18DB
• DAMPING FACTOR GREATER THAN: 200
• FREQUENCY RESPONSE: 10HZ - 20KHZ
• HIGH AND LOW PASS CROSSOVER: 12DB PER OCTAVE
• HIGH LEVEL INPUT RANGE: 1 VOLT TO 30 VOLTS
• LOW LEVEL INPUT RANGE: 0.35 VOLTS TO 10 VOLTS
• LOW PASS CROSS OVER RANGE: 50HZ - 250HZ
• MINIMUM LOAD IMPEDANCE: 2 OHM
• NUMBER OF CHANNELS: 3
• OPERATING VOLTAGE: 10.5 - 16 VOLTS
• POWER (WATTS): 2400
• POWER REQUIREMENTS: 12V DC (NEGATIVE GROUND)
• RECOMMENDED MINIMUM POWER/GROUND: 4 GAUGE (AWG) CABLE
• RMS POWER OUTPUT @ 14.4V: 1% THD+N FRONT 90W X2 @ 4 OHM, 150W X 2 @ 2 OHM
• RMS POWER OUTPUT @ 14.4V: 1% THD+N SUB 235W X 1 @ 4 OHM, 400W X 1 @ 2 OHM
• SIGNAL TO NOISE RATIO: >50DB
• SUBSONIC CROSSOVER RANGE: 10HZ - 40HZ
• SUBSONIC FILTER: 12DB PER OCTAVE

FEATURES

• HIGH PERFORMANCE HIGH-SLEW RATE OPERATIONAL AMP: THE PRS AMPLIFIER INCLUDES LINEAR TECHNOLOGY CORPORATION’S HIGH-PERFORMANCE HIGH-SLEW RATE OPERATIONAL AMPLIFIER IN THE CIRCUITRY THAT GENERATES PWM (PULSE WIDTH MODULATION) SIGNALS FROM ANALOG INPUT SIGNALS WITH AMAZING ACCURACY. THE RESULT: VERY LINEAR MUSIC REPRODUCTION WITH LOW DISTORTION RATE.
• ELECTROLYTIC CAPACITOR FOR AUDIO: EXTENSIVE LISTENING TESTS WENT INTO SELECTING AND MOUNTING AN AUDIO CAPACITOR FOR OPTIMAL AUDIO FREQUENCY RESPONSE AND DYNAMIC RANGE THAT ARE CHARACTERISTICS OF HIGH-END SOUND TONE AND DETAIL.
• OFC (OXYGEN-FREE COPPER) WIRE COIL FOR OUTPUT: THE LPF OUTPUT OF THE CLASS-FD AMPLIFIER FEATURES OFC WIRE COIL FOR LOW DC (DIRECT CURRENT) RESISTANCE AND LOW LOSS, SO THAT SPEAKERS CAN BE DRIVEN STRONGLY TO PRODUCE TIGHT BASS AND A CLEAR, VIVID MID- AND HIGH-RANGE SOUND.
• TVC (TOTAL VIBRATION CONTROL): ANTI-VIBRATION MATERIAL UNDER THE TRANSFORMER THOROUGHLY ELIMINATES VIBRATION THAT NORMALLY BLOCKS SOUND WHEN HIGH CURRENT IS APPLIED, ENHANCING POWER FLOW STABILITY, MINIMIZING DISTORTION, AND RAISING SIGNAL-TO-NOISE RATIO.

SPECIFICATIONS

• MAXIMUM POWER: 600 W
• FREQUENCY RESPONSE: 10 - 30.000
• INPUT LEVEL CONTROL: 400 MV TO 6.5 V (A/B INDEPENDENT)
• DISTORTION: <0.004
• S/N RATIO: >105
• MAX. CURRENT CONSUMPTION: 6.4 A / 4 Ω FOR TWO CHANNELS
• CHASSIS SIZE (W X H X D): 255 X 50 X 104
• UNIT WEIGHT: 1.6
• CONTINUOUS POWER OUTPUT:
• 125 W RMS X 2 CHANNELS (AT 14.4V, 4 Ω)
• 150 W RMS X 2 CHANNELS (AT 14.4V, 2 Ω)
• 300 W RMS X 1 CHANNEL (AT 14.4V, 4 Ω BRIDGE)
• CAR AMPLIFIER GROUP: YES
• PIONEER REFERENCE SERIES (PRS): YES
• LOAD IMPEDANCE CAPABILITY: 2 Ω - 8 Ω STEREO
• CEA 2006 POWER:
• 2 CHANNELS AT 14.4V, 4 Ω
• 2 CHANNELS AT 14.4V, 2 Ω
• 1 CHANNEL AT 14.4V, 4 Ω BRIDGE
• RCA TERMINALS: 2-CH. (GOLD-PLATED)
• HIGH VOLTAGE INPUT CAPABILITY: YES
• SPEAKER TERMINALS: SCREW-TYPE
• 2-CHANNEL: YES
• HIGH PERFORMANCE BALANCED ISOLATOR CIRCUIT: 
• COMPACT SIZE: YES
• MOSFET OUTPUT SECTION: YES
• D-CLASS: YES

• POWER @ 4-OHM: 200W × 1
• POWER @ 2-OHM: 300W × 1
• BRIDGED POWER @ 4-OHM: －
• NUMBER OF CHANNELS: 1
• MOS-FET POWER SUPPLY: YES
• 2-OHM STABLE: YES
• SELECTABLE BASS BOOST: 0-12DB @ 50HZ
• ADJUSTABLE 12DB/OCT. LOW PASS CROSSOVER: VARIABLE 35 - 250HZ
• NICKEL PLATED CONNECTORS: RCA/ SPEAKER/ POWER
• DIMENSIONS (W × H × D) (INCHES): 7.85 × 1.54 × 3.23

• 400 WATTS OF MAXIMUM POWER OUTPUT
• 50 WATTS × 4 CONTINUOUS @ 4-OHMS
• 75 WATTS × 4 CONTINUOUS @ 2-OHMS
• 150 WATTS × 2 CONTINUOUS @ 4-OHMS BRIDGED
• DOUBLE SIDE CONFORMAL COATED PCB ASSEMBLY
• MOS-FET POWER SUPPLY
• 12DB/OCT. HIGH PASS ELECTRONIC CROSSOVER. VARIABLE 15 - 250HZ (FR/RR)
• VARIABLE GAIN CONTROL
• TURN-ON/OFF MUTING CIRCUITRY (SOFT MUTE)
• GROUND LOOP ISOLATION INPUT CIRCUIT
• CORROSION RESISTANT NICKEL PLATED RCA, POWER, AND SPEAKER CONNECTIONS
• RCA AND HIGH LEVEL SPEAKER INPUTS

•  
• 1300 WATTS OF MAXIMUM MUSIC POWER
• 650 WATTS X 1 CONTINUOUS @ 2-OHMS
• 330 WATTS × 1 CONTINUOUS @ 4-OHMS
• ADJUSTABLE - 12DB/OCT. LOW PASS ELECTRONIC CROSSOVER, 50HZ-500HZ
• BASS EXTENDER CONTROL, 0-12DB AT 45HZ
• ADJUSTABLE INFRASONIC FILTER, 10-50HZ
• PHASE CONTROL, 0-180 DEGREES
• BC2 REMOTE SUBWOOFER LEVEL CONTROL INCLUDED
• SOFT TURN-ON AND TURN-OFF CIRCUITRY
• AUDIO PASS-THROUGH OUTPUTS FOR ADDITIONAL AMPLIFIERS
• CONFORMALLY COATED PC BOARD
• STAINLESS HARDWARE
• MOS-FET POWER SUPPLY
• GROUND LOOP ISOLATION CIRCUIT
• CORROSION RESISTANT NICKEL PLATED RCA, POWER, AND SPEAKER CONNECTIONS

SPECIFICATIONS:

• NUMBER OF CHANNELS: 4 - CHANNEL
• MINIMUM IMPEDANCE UNBRIDGED: 2 OHM
• MINIMUM IMPEDANCE BRIDGED: 4 OHM
• SPEAKER LEVEL INPUTS: YES
• MAXIMUM INPUT GAUGE SIZE: 4 GAUGE
• AMPLIFIER CLASS: A/B
• SERIES: LOADED (FLI)
• BUILT IN CROSSOVER: FULL (AP)
• COMBINED RMS POWER OUTPUT: 400
• COMBINED PEAK POWER OUTPUT: 800
• PREAMP OUTPUTS: 1
• THD: 0.05%
• S/N RATIO: 95DB
• DIMENSIONS: 350 X 180 X 50 MM
• DAMPING FACTOR: 100
• RMS OUTPUT @ 4 OHMS: 4 X 80
• RMS OUTPUT @ 2 OHMS: 4 X 100
• RMS OUTPUT BRIDGED @ 4 OHMS: 2 X 200

SPECIFICATIONS:

• POWER (WATTS) 1200
• RMS POWER OUTPUT @ 14.4V 1% THD+N 200W X 1 (@4 OHM)
• RMS POWER OUTPUT @ 14.4V 1% THD+N 300W X 1 (@ 2 OHM)
• AMPLIFIER TYPE CLASS-AB
• NUMBER OF CHANNELS 1
• FREQUENCY RESPONSE 20HZ - 400HZ
• SIGNAL TO NOISE RATIO >50DB
• SUBSONIC CROSSOVER RANGE 10HZ - 40HZ
• HIGH AND LOW PASS CROSSOVER 12DB PER OCTAVE
• SUBSONIC FILTER 12DB PER OCTAVE
• LOW PASS CROSS OVER RANGE 50HZ - 400HZ
• BASS BOOST @ 45HZ 0 - +18DB
• LOW LEVEL INPUT RANGE 0.35 VOLTS TO 10 VOLTS
• HIGH LEVEL INPUT RANGE 1 VOLT TO 30 VOLTS
• MINIMUM LOAD IMPEDANCE 2 OHM
• DAMPING FACTOR GREATER THAN 200
• POWER REQUIREMENTS 12V DC (NEGATIVE GROUND)
• OPERATING VOLTAGE 10.5 - 16 VOLTS
• RECOMMENDED MINIMUM POWER/GROUND 4 GAUGE (AWG) CABLE
• LENGTH 336MM (13-1/4")
• WIDTH 200MM (7-7/8")
• HEIGHT 51MM (2")

• AMPLIFIER TYPE: CLASS-AB
• BASS BOOST @ 45HZ: 0 - +18DB
• CROSSOVER RANGE: 50HZ - 400HZ
• DAMPING FACTOR: GREATER THAN 200
• FREQUENCY RESPONSE: 20HZ - 20KHZ
• HIGH AND LOW PASS CROSSOVER: 12DB PER OCTAVE
• HIGH LEVEL INPUT RANGE: 1 VOLT TO 30 VOLTS
• LOW LEVEL INPUT RANGE: 0.35 VOLTS TO 10 VOLTS
• MINIMUM LOAD IMPEDANCE: 2 OHM STEREO AND 4 OHM BRIDGED
• NUMBER OF CHANNELS: 2
• OPERATING VOLTAGE: 10.5 - 16 VOLTS
• POWER (WATTS): 1200
• POWER REQUIREMENTS: 12V DC (NEGATIVE GROUND)
• RECOMMENDED MINIMUM POWER/GROUND: 4 GAUGE (AWG) CABLE
• RMS POWER OUTPUT @ 14.4V 1% THD+N: 90W X 2 (@ 2 OHM)
• RMS POWER OUTPUT @ 14.4V 1% THD+N: 180W X 1 (@4 OHM BRIDGED)
• RMS POWER OUTPUT @ 14.4V 1% THD+N: 65W X 2 (@ 4 OHM)
• SIGNAL TO NOISE RATIO: >50DB

• POWER (WATTS) 1600
• RMS POWER OUTPUT @ 14.4V 1% THD+N 250W X 1 (@4 OHM)
• RMS POWER OUTPUT @ 14.4V 1% THD+N 400 X 1 (@ 2 OHM)
• AMPLIFIER TYPE CLASS-D
• NUMBER OF CHANNELS 1
• FREQUENCY RESPONSE 10HZ - 250HZ
• SIGNAL TO NOISE RATIO >50DB
• HIGH AND LOW PASS CROSSOVER 12DB PER OCTAVE
• BASS BOOST @ 45HZ 0 - +18DB
• LOW LEVEL INPUT RANGE 0.35 VOLTS TO 10 VOLTS
• HIGH LEVEL INPUT RANGE 1 VOLT TO 30 VOLTS
• MINIMUM LOAD IMPEDANCE 2 OHM
• DAMPING FACTOR GREATER THAN 200
• POWER REQUIREMENTS 12V DC (NEGATIVE GROUND)
• OPERATING VOLTAGE 10.5 - 16 VOLTS
• RECOMMENDED MINIMUM POWER/GROUND 4 GAUGE (AWG) CABLE
• SUBSONIC FILTER 12DB PER OCTAVE
• LOW PASS CROSS OVER RANGE 50HZ - 250HZ
• SUBSONIC CROSSOVER RANGE 10HZ - 40HZ
• LENGTH 236MM (9-1/4")
• WIDTH 200MM (7-7/8")
• HEIGHT 51MM (2")

FEATURES

• CLASS-D AMPLIFIER TECHNOLOGY: THE HIGHLY EFFICIENT CLASS-D DESIGN PROVIDES 1400-WATTS PEAK POWER WHILST DRAWING LESS CURRENT THAN A STANDARD CLASS-AB AMPLIFIER. THIS DESIGN PROVIDES INCREASED EFFICIENCY AND POWER OUTPUT TO YOUR SPEAKERS, LETTING YOU ENJOY YOUR MUSIC FOR LONGER.
• 1400 WATTS PEAK POWER: EASILY POWER 4 SPEAKERS, OR 2 SPEAKERS AND A SUBWOOFER WITH A PEAK POWER OF 1400 WATTS.
• MARINE-READY DESIGN WITH CONFORMAL COATED PCBS: EXTENDING THE LIFE OF YOUR AMPLIFIERS, THE SIGNATURE SERIES ARE DESIGNED SPECIFICALLY FOR MARINE USE WITH CONFORMAL COATED PCBS TO PROVIDE EXTRA PROTECTION FROM THE MARINE ELEMENTS.
• RIGID ALUMINUM ALLOY HEAT SINK: MOLDED TO FORM A SINGULAR DIE-CAST CHASSIS, THE FIN LAYOUT IS CALCULATED WITH PRECISION TO INCREASE THE SURFACE AREA OF THE HEAT SINK AND IMPROVE HEAT DISSIPATION.
• STAINLESS MIRROR FINISH: THE POLISHED STAINLESS STEEL CONTROL PANEL COVER CONCEALS AND PROTECTS ALL CABLE CONNECTIONS AND SETTINGS CONTROLS WHILST PROVIDING AN ATTRACTIVE FINISH TO COMPLEMENT ANY INSTALLATION.
• SPEAKER CONFIGURATION: WHETHER YOU REQUIRE 2 OHMS PER CHANNEL OR 4 OHMS BRIDGED, YOUR SIGNATURE SERIES AMPLIFIER HAS YOUR INSTALLATION OPTIONS COVERED TO ACHIEVE THE OPTIMUM OUTPUT LEVELS.
• CONNECT UP TO TWO SPEAKERS PER CHANNEL AT 2 OHMS, OR FOR EXTRA POWER, BRIDGE TWO CHANNELS AT 4 OHMS TO CONNECT TWO SUBWOOFERS.
• ZONE DESIGNATION: TO ALIGN WITH THE FUSION ENTERTAINMENT SYSTEM ZONE PHILOSOPHY, THE INPUT AND OUTPUT CONNECTIONS ARE LABELLED AS ZONES.
• TRUE-MARINE DESIGN: SIGNATURE SERIES AMPLIFIERS ARE PERFECT FOR THE MARINE ENVIRONMENT, AND CARRY A 3-YEAR WARRANTY.

SPECIFICATIONS

• AMPLIFIER CLASS: CLASS-D
• FREQUENCY RESPONSE: 10HZ - 65KHZ
• PEAK POWER: 1400 WATTS
• RATED POWER (4 OHMS): 150 WATTS RMS X 4 @ 14.4V - 4 OHMS 1% THD
• RATED POWER (2 OHMS): 220 WATTS RMS X 4 @ 14.4V - 2 OHMS 1% THD
• RATED POWER (4 OHMS BRIDGED): 440 WATTS RMS X 2 @ 14.4V - 4 OHM BRIDGED 1% THD

DIMENSIONS

• HEIGHT: 50MM [2”]
• LENGTH: 300MM [11-13/16”]
• DEPTH: 210MM [8-1/4”]

FEATURES:

• CLASS-D AMPLIFIER TECHNOLOGY - ENJOY YOUR MUSIC FOR LONGER AND TAKE YOUR AUDIO ENTERTAINMENT EXPERIENCE TO A WHOLE NEW LEVEL WITH AMPLIFIERS THAT ARE BUILT FOR HIGH PERFORMANCE. THE HIGHLY EFFICIENT CLASS-D DESIGN DRAWS LESS CURRENT THAN A STANDARD CLASS-AB AMPLIFIER, PROVIDING INCREASED EFFICIENCY AND POWER OUTPUT TO YOUR SPEAKERS. 
• MARINE-READY DESIGN - EXTENDING THE LIFE OF YOUR AMPLIFIERS, THE SIGNATURE SERIES ARE DESIGNED SPECIFICALLY FOR MARINE USE WITH CONFORMAL COATED PCBS TO PROVIDE EXTRA PROTECTION FROM THE MARINE ELEMENTS.
• RIGID ALUMINUM ALLOY HEAT SINK - MOLDED TO FORM A SINGULAR DIE-CAST CHASSIS, THE FIN LAYOUT IS CALCULATED WITH PRECISION TO INCREASE THE SURFACE AREA OF THE HEAT SINK AND IMPROVE HEAT DISSIPATION.
• STAINLESS MIRROR FINISH - THE POLISHED STAINLESS STEEL CONTROL PANEL COVER CONCEALS AND PROTECTS ALL CABLE CONNECTIONS AND SETTINGS CONTROLS WHILST PROVIDING AN ATTRACTIVE FINISH TO COMPLEMENT ANY INSTALLATION.

SPECIFICATIONS:

• AMPLIFIER CLASS: CLASS-D
• SUBWOOFER FREQUENCY RESPONSE: 10HZ - 50KHZ
• PEAK POWER: 1600 WATTS
• RATED POWER (4 OHMS): 80 WATTS RMS X 4 + 250 WATTS RMS X 1 @ 14.4V - 4 OHMS 1% THD
• RATED POWER (2 OHMS): 130 WATTS RMS X 4 + 330 WATTS RMS X 1 @ 14.4V - 2 OHMS 1% THD
• RATED POWER (4 OHMS BRIDGED): 250 WATTS RMS X 2 @ 14.4V - 4 OHMS BRIDGED 1% THD + 250 WATTS RMS X 1 @ 14.4V - 4 OHMS 1% THD
• GIFT BOX DIMENSION: (W) 379MM (14-15/16”) (H) 110MM (4-5/16”) (D) 268MM (10-9/16”)
• MOUNTING DIMENSIONS:
• HEIGHT: 50MM [2”]
• LENGTH: 300MM [11-13/16”]
• DEPTH: 210MM [8-1/4”]

• PEAK POWER: 1500W
• FREQUENCY RESPONSE: 10HZ - 50KHZ - 3DB
• AMPLIFIER CLASS: CLASS D
• TOTAL RATED POWER (4 OHMS): 6 X 110W RMS @ 14.4VDC INPUT, 4 OHM, 1% THD
• TOTAL RATED POWER (2 OHMS): 6 X 200W RMS @ 14.4VDC INPUT, 2 OHM, 1% THD
• TOTAL RATED POWER (4 OHMS BRIDGED): 3 X 400W RMS @ 14.4VDC INPUT, 4 OHM BRIDGED, 1% THD
• OPERATING VOLTAGE: 10.8 - 16VDC
• MOUNTING DIMENSIONS (D X H X L): 210 X 57 X 420MM (8-1/4” X 2-1/4” X 16-9/16”)

• PEAK POWER: 2000W
• FREQUENCY RESPONSE: 10HZ - 50KHZ - 3DB
• AMPLIFIER CLASS: CLASS D
• TOTAL RATED POWER (4 OHMS): 8 X 110W RMS @ 14.4VDC INPUT, 4 OHM, 1% THD
• TOTAL RATED POWER (2 OHMS): 8 X 200W RMS @ 14.4VDC INPUT, 2 OHM, 1% THD
• TOTAL RATED POWER (4 OHMS BRIDGED): 4 X 400W RMS @ 14.4VDC INPUT, 4 OHM BRIDGED, 1% THD
• OPERATING VOLTAGE: 10.8 - 16VDC
• MOUNTING DIMENSIONS (D X H X L): 210 X 57 X 420MM (8-1/4” X 2-1/4” X 16-9/16”)

FEATURES

• ULTRA-COMPACT - EXCELLENT FOR OEM SYSTEMS UPGRADE, THE DPOWER AMPLIFIERS ARE ULTRA-COMPACT TO ENSURE EFFORTLESS INSTALLATIONS IN THE INCREASINGLY NARROW SPACES OF MODERN VEHICLES OR IN THE FACTORY AMP AREA
• HIGH POWER/SIZE RATIO - THE EFFICIENT D CLASS CIRCUIT DELIVERS 600 W OF MAXIMUM POWER WITHIN A COMPACT CHASSIS, AN ESSENTIAL REQUIREMENT FOR IN-CAR INTEGRATION
• VERSATILE X-OVER - DPOWER1 BASS BOOST FUNCTION ENHANCES 45 HZ UP TO 12 DB TO INCREASE SUBWOOFER PUNCH
• SPEAKER & RCA INPUTS - THE DOUBLE SPEAKER & RCA INPUTS ALLOWS THE DPOWER AMPLIFIERS TO CONNECT TO ANY TYPE OF SOURCE, BE IT OEM OR AFTERMARKET
• ART AUTO TURN-ON/OFF - FOR AN EXCELLENT INTEGRATION WITH OEM SYSTEMS THE DPOWER AMPLIFIERS ARE EQUIPPED WITH A SMART AUTOMATED TURN ON AND OFF CIRCUIT ACCORDING TO THE FACTORY RADIO

SPECIFICATIONS

• CHANNEL MODE: 1
• OUTPUT POWER (RMS) @ 14.4 VDC: 1 CH 180 W X 1 (4Ω) / 1 CH 300 W X 1 (2Ω)
• DISTORTION - THD (100HZ @ 4Ω): 0.1 %
• S/N RATIO (A WEIGHTED @ 1V): 105 DB
• DAMPING FACTOR (100HZ @ 4Ω): 100
• SIZE W X D X H MM (IN.): 222,2 X 160 X 50,5 / 8,75 X 6,3 X 1,99
• FILTERS

1. BYPASS: YES
2. HI-PASS: NOT AVAILABLE
3. LO-PASS: 50 ÷ 220 HZ @ 12 DB/OCT.
4. BAND-PASS: NOT AVAILABLE
5. SUBSONIC: NOT AVAILABLE

FEATURES:

• ULTRA-COMPACT - EXCELLENT FOR OEM SYSTEMS UPGRADE, THE DPOWER AMPLIFIERS ARE ULTRA-COMPACT TO ENSURE EFFORTLESS INSTALLATIONS IN THE INCREASINGLY NARROW SPACES OF MODERN VEHICLES OR IN THE FACTORY AMP AREA
• HIGH POWER/SIZE RATIO - THE EFFICIENT D CLASS CIRCUIT DELIVERS 600 W OF MAXIMUM POWER WITHIN A COMPACT CHASSIS, AN ESSENTIAL REQUIREMENT FOR IN-CAR INTEGRATION
• VERSATILE X-OVER - DPOWER BASS BOOST FUNCTION ENHANCES 45 HZ UP TO 12 DB TO INCREASE SUBWOOFER PUNCH
• SPEAKER & RCA INPUTS - THE DOUBLE SPEAKER & RCA INPUTS ALLOWS THE DPOWER AMPLIFIERS TO CONNECT TO ANY TYPE OF SOURCE, BE IT OEM OR AFTERMARKET
• ART AUTO TURN-ON/OFF - FOR AN EXCELLENT INTEGRATION WITH OEM SYSTEMS THE DPOWER AMPLIFIERS ARE EQUIPPED WITH A SMART AUTOMATED TURN ON AND OFF CIRCUIT ACCORDING TO THE FACTORY RADIO

SPECIFICATIONS:

• CHANNEL MODE: 2-4
• DISTORTION - THD (100HZ @ 4Ω): 0.2%
• S/N RATIO (A WEIGHTED @ 1V): 95 DB
• DAMPING FACTOR (100HZ @ 4Ω): 60
• SIZE W X D X H MM (IN.): 222.2 X 160 X 50.5 / 8.75 X 6.3 X 1.99
• OUTPUT POWER (RMS) @ 14.4 VDC:
• 4 CH 60 W X 4 (4Ω)
• 4 CH 75 W X 4 (2Ω)
• 2 CH 150 W X 2 (4Ω)
• 3 CH 60 W X 2 + 150 W X 1 (4Ω)
• 3 CH 75 W X 2 + 150 W X 1 (2Ω)
• FILTERS
• BYPASS: YES
• HI-PASS: 40 ÷ 220 HZ @ 12 DB/OCT.
• LO-PASS: 40 ÷ 220 HZ @ 12 DB/OCT.
• BAND-PASS: NOT AVAILABLE
• SUBSONIC: NOT AVAILABLE

• CHANNEL MODE: 1
• OUTPUT POWER (RMS) 14.4 VDC:
• 1 CH: 380 W X 1 (4 Ω)
• 1 CH: 700 W X 1 (2 Ω)
• FILTERS
• BYPASS: YES
• HI-PASS: -
• LO-PASS:50 ÷ 250 HZ @ 24 DB/OCT.
• BAND-PASS:-
• SUBSONIC:25 HZ @ 24 DB/OCT.
• DISTORTION - THD (100HZ @ 4Ω): 0.2%
• S/N RATIO (A WEIGHTED @ 1V): 100 DB
• DAMPING FACTOR (100HZ @ 4Ω): 80
• SIZE W X D X H MM (IN.): 215 X 190 X 50 (8.46 X 7.48 X 1.97

SPECIFICATIONS

• CHANNEL MODE: 1
• OUTPUT POWER (RMS) @ 14.4 VDC:
• 1 CH: 740 W X 1 (4Ω)
• 1 CH: 1240 W X 1 (2Ω)
• FILTERS
• BYPASS:
• HI-PASS: 50 ÷ 250 HZ @ 12 DB/OCT.
• LO-PASS: 50 ÷ 250 HZ @ 24 DB/OCT.
• BAND-PASS:
• SUBSONIC: 25 HZ @ 24 DB/OCT.
• DISTORTION - THD (100HZ @ 4Ω): 0,25 %
• S/N RATIO (A WEIGHTED @ 1V): > 100 DB
• DAMPING FACTOR: (100HZ @ 4Ω) > 100
• SIZE W X D X H MM (IN.): 315 X 190 X 50 (12.40 X 7.48 X 1.97)
   

TECHNOLOGIES
REFINED HEATSINK WITH HIGH CONVECTION CAPABILITY
The extruded aluminum heatsink provides high efficiency thermal performance; using the top side of the heatsink to effectively dissipate the heat generated by the electronic components. The internal temperature remains constant at all power levels.

COMPLETED FILTER SECTION
Large array of filters customized for each model, to achieve maximum versatility: Lo-Pass, Hi-Pass, Band-Pass, Full Range, Subsonic, Bass Boost, Phase and Mono. Filtered pre-amplified outputs along with multiple adjustments are featured on the HCP 1D, offering the user endless connection possibilities with any source.

HCP ELECTRONICS
Special balanced input circuitry rejects electro-magnetic disturbances present on the Pre-amplified or Speaker level inputs. Power supply stage features a multiple winding transformer and Low-ESR 105.

ART
Automatic Remote Turn-On/Off function, automatically turns the amplifier on and off with the OEM radio; eliminates the need for a remote signal from the source when using the Speaker-In. This function can also be disabled.

SPECIFICATIONS

• CHANNEL MODE: 2 - 1
• OUTPUT POWER (RMS) @ 14.4 VDC:
• 2 CH: 65 W X 2 (4Ω)
• 2 CH: 100 W X 2 (2Ω)
• 1 CH: 200 W X 1 (4Ω)
• FILTERS
• BYPASS: YES
• HI-PASS: 80 HZ @ 12 DB/OCT.
• LO-PASS: 50
• BAND-PASS: -
• DISTORTION - THD (100HZ @ 4Ω): 0.01%
• S/N RATIO (A WEIGHTED @ 1V): 103 DB
• DAMPING FACTOR (100HZ @ 4Ω): 200
• SIZE W X D X H MM (IN.): 215 X 190 X 50 (8.46 X 7.48 X 1.97)
   

TECHNOLOGIES
REFINED HEATSINK WITH HIGH CONVECTION CAPABILITY
The extruded aluminum heatsink provides high efficiency thermal performance; using the top side of the heatsink to effectively dissipate the heat generated by the electronic components. The internal temperature remains constant at all power levels.

COMPLETED FILTER SECTION
Large array of filters customized for each model, to achieve maximum versatility: Lo-Pass, Hi-Pass, Band-Pass, Full Range, Subsonic, Bass Boost, Phase and Mono. Filtered pre-amplified outputs along with multiple adjustments are featured on the HCP 1D, offering the user endless connection possibilities with any source.

HCP ELECTRONICS
Special balanced input circuitry rejects electro-magnetic disturbances present on the Pre-amplified or Speaker level inputs. Power supply stage features a multiple winding transformer and Low-ESR 105.

ART
Automatic Remote Turn-On/Off function, automatically turns the amplifier on and off with the OEM radio; eliminates the need for a remote signal from the source when using the Speaker-In. This function can also be disabled.

SPECIFICATIONS

• CHANNEL MODE: 4 - 3 - 2
• OUTPUT POWER (RMS) @ 14.4 VDC:
• 4 CH: 65 W X 4 (4 Ω)
• 4 CH: 95 W X 4 (2 Ω)
• 3 CH: 65 W X 2 (4 Ω) + 190 W X 1 (4 Ω)
• 3 CH: 95 W X 2 (2 Ω) + 190 W X 1 (4 Ω)
• 2 CH: 190 W X 2 (4 Ω)
• FILTERS
• BYPASS: YES
• HI-PASS: A/B: 80 HZ @ 12 DB/OCT.
• LO-PASS: A/B: 50 ÷ 500 HZ @ 12 DB/OCT.
• BAND-PASS: -
• DISTORTION - THD (100HZ @ 4Ω): 0.01%
• S/N RATIO (A WEIGHTED @ 1V): 103 DB
• DAMPING FACTOR (100HZ @ 4Ω): 120
• SIZE W X D X H MM (IN.): 315 X 190 X 50 (12.40 X 7.48 X 1.97
   

TECHNOLOGIES

REFINED HEATSINK WITH HIGH CONVECTION CAPABILITY
The extruded aluminum heatsink provides high efficiency thermal performance; using the top side of the heatsink to effectively dissipate the heat generated by the electronic components. The internal temperature remains constant at all power levels.

COMPLETED FILTER SECTION
Large array of filters customized for each model, to achieve maximum versatility: Lo-Pass, Hi-Pass, Band-Pass, Full Range, Subsonic, Bass Boost, Phase and Mono. Filtered pre-amplified outputs along with multiple adjustments are featured on the HCP 1D, offering the user endless connection possibilities with any source.
COMPLETED FILTER SECTION
Large array of filters customized for each model, to achieve maximum versatility: Lo-Pass, Hi-Pass, Band-Pass, Full Range, Subsonic, Bass Boost, Phase and Mono. Filtered pre-amplified outputs along with multiple adjustments are featured on the HCP 1D, offering the user endless connection possibilities with any source.
ART
Automatic Remote Turn-On/Off function, automatically turns the amplifier on and off with the OEM radio; eliminates the need for a remote signal from the source when using the Speaker-In. This function can also be disabled.

• CHANNEL MODE - 1
• OUTPUT (RMS) - 1CH / 600W X 1 @ 4OHM, 1CH / 1000W X 1
• FILTERS - LO-PASS: 40/150HZ @ 24DB/OCT. - SUBSONIC: 18/40HZ @ 24B/OCT.
• DISTORTION / THD (100HZ @ 4OHM) - 0.08%
• S/N RATIO - 103DB
• DAMPING FACTOR (100HZ @ 4OHM) - 100
• DIMENTIONS W X D X H MM - 171 X 344 X 46.70

SPECIFICATIONS

• ​CHANNEL MODE: 5-3
• OUTPUT POWER (RMS): 
• @ 14.4 VDC 5 CH 70 W X 4 + 380 W X 1 (4Ω)
• 5 CH 100 W X 4 + 550 W X 1 (2Ω)
• 3 CH 200 W X 2 (4Ω) + 380 W X 1 (4Ω)
• 3 CH 200 W X 2 (4Ω) + 550 W X 1 (2Ω)
• FILTERS
• BYPASS: YES
• HI-PASS: 40 ÷ 150 HZ (HI) 80 ÷ 3.3K HZ (LO) @ 12 DB/OCT
• LO-PASS: 40 ÷ 150 HZ @ 24 DB/OCT.
• BAND-PASS: 40 ÷ 150 HZ (HI) 80 ÷ 3.3K HZ (LO) @ 12 DB/OCT
• DISTORTION - THD (100HZ @ 4Ω): 0.08 %
• S/N RATIO (A WEIGHTED @ 1V) :
• A & B CH - 100 DB
• C CH - 106 DB
• DAMPING FACTOR (100HZ @ 4Ω):
• A & B CH - 50
• C CH - 100
• SIZE W X D X H MM (IN.): 171 X 344 X 46,.70 (6.73 X 13.54 X 1.83)
   

TECHNOLOGIES

MONITORING LEDS
4 LEDs monitor amplifier status and communicate with the user in real time. This system, while allowing the amplifier to operate, also identifies installation faults and leads to eliminate them.


HDP ELECTRONICS
Power supply stage featuring toroidal transformers with multi-layered windings, powerful TO220 Mosfets.
 

ADVANCED HEATSINK
The heatsink boasts extremely efficient thermal conductivity, combined with exclusive cosmetics: scratch-resistant finish, end caps shaped for easy handling, control panel accessible from the top as well as a featured back lit Hertz logo which can also be rotated.

HDP IN & ART(TM)
HDP IN system provides to interface with any OEM (through the Speaker In) and aftermarket (through the RCA In) sources. Using Speaker In inputs, the ART (Automatic Remote Turn On-Off) function is available; the user can also switch it off.

FEATURES

• NATURE PROOF: ENGINEERED AND TESTED FOR THE REAL ENVIRONMENT OF APPLICATION (UV, SALT-FOG, VIBRATIONS, HIGH/LOW TEMPERATURE, THERMAL SHOCK, DUST).
• COMPACT, CAST-ALUMINIUM CHASSIS: COMPACT, CAST-ALUMINUM CHASSIS (IPX6 RATED), MAKING THEM THE IDEAL CHOICE FOR POWERSPORTS/MARINE/MOTORCYCLE INSTALLATIONS.
• BASS BOOST: BASS BOOST ADJUSTABLE VIA SELECTOR, FOR MORE PUNCH FROM SPEAKERS.

SPECIFICATIONS

• CHANNEL MODE - 1
• OUTPUT POWER (RMS) @ 14.4 VD - 180 W X 1 (4 Ω) 300 W X 1 (2 Ω)
• FILTERS

1. BYPASS - YES
2. HI-PASS - NA
3. LO-PASS - 65-85-115 HZ @ 12 DB/OCT.
4. BAND-PASS - NA
5. SUBSONIC - OFF-22-32 HZ @ 12 DB/OCT.

• DISTORTION THD (100HZ @ 4Ω) 0.1 % - 0.1%
• S/N RATIO (A WEIGHTED @ 1V) - 105 DB
• DAMPING FACTOR (100HZ @ 4Ω) - 300
• SIZE W X D X HMM (IN.) - 223 X 100.5 X 43.6 (8.77 X 3.95 X 1.71)

FEATURES

• NATURE PROOF: ENGINEERED AND TESTED FOR THE REAL ENVIRONMENT OF APPLICATION (UV, SALT-FOG, VIBRATIONS, HIGH/LOW TEMPERATURE, THERMAL SHOCK, DUST).
• COMPACT, CAST-ALUMINIUM CHASSIS: COMPACT, CAST-ALUMINUM CHASSIS (IPX6 RATED), MAKING THEM THE IDEAL CHOICE FOR POWERSPORTS/MARINE/MOTORCYCLE INSTALLATIONS.
• BASS BOOST: BASS BOOST ADJUSTABLE VIA SELECTOR, FOR MORE PUNCH FROM SPEAKERS.

SPECIFICATIONS

• CHANNEL MODE - 4\2
• OUTPUT POWER (RMS) @ 14.4 VD - 60 W X 4 (4 Ω), 75 W X 4 (2 Ω), 150 W X 2 (4 Ω)
• FILTERS

1. BYPASS - YES
2. HI-PASS - 65-85-115 HZ @ 12 DB/OCT.
3. LO-PASS - 65-85-115 HZ @ 12 DB/OCT.

• DISTORTION THD (100HZ @ 4Ω) 0.2%
• S/N RATIO (A WEIGHTED @ 1V) - 95 DB
• DAMPING FACTOR (100HZ @ 4Ω) - 45
• SIZE W X D X HMM (IN.) - 223 X 100.5 X 43.6 (8.77 X 3.95 X 1.71)